Mangrove Jack's Kegerator Series Скачать руководство пользователя страница 5

Страница: 5 / 12

BREWING.

OUR OBSESSION.

5. FITTING YOUR CO

CYLINDER

• Slide your fully charged

CO2

cylinder into the stand.

NOTE:

You will need to have purchased this separately.

• If your cylinder is too big to fit onto the stand, you can have this sitting on the ground

behind the Kegerator and may not need to attach the cylinder support.

6. ATTACHING THE BEER TOWER TO THE KEGERATOR

• Remove the hole cover on top of the Kegerator.
• Place the rubber gasket around the hole in the top of the Kegerator. Line up the

screw holes.

• Feed the tubes that run through the Beer Tower through the centre hole in the

top of the Kegerator.

• Sit the Beer Tower on top of the Kegerator, lining up the screw holes with the rubber

gasket and the Kegerator screw holes.

• Use the remaining screws to screw on the Beer Tower. Be sure to screw it

in tightly.

NOTE:

Lift the cover at the base of the Beer Tower to find the screw holes.

• Screw on the black tap handles.

4. ATTACHING THE CO2 CYLINDER SUPPORT

• Attach the cylinder support rack onto the 4 studs located at the back of the Kegerator.

Align the holes in the cylinder support with the studs and push down firmly.

Содержание Kegerator Series












