background image

TPM 092/13

3

II. GENERAL INFORMATION

1. Description

1.1.  

Fire dampers are shutters in piping systems of air-conditioning devices that prevent spreading 
the fire and combustion products from one fire segment to the other one by means of closing the 
air piping in the points of fire separating constructions.

1.2.  

Basic dampers parameters

 

- fire damper tests provided according to EN 1366-2 and EN 15650.

 

- fire damper classified according to EN 13501-3 + A1 as

 

  

EI 90 (ve ho i    o) S

 

 - casing (external) leakage classified as class C according to EN 1751

 

- closed blade (internal) leakage classified as class 2 according to EN 1751

 

- fulfil all the prescribed requirements of EN 15650, art. 4.2.2. Protection against corrosion 

 

- dampers are classified as C10000 (cycling test) according to EN 15650

1.3.  

Dampers blade automatically closes air duct using a shutting spring or an actuating mechanism 
back spring. The back spring of the actuating mechanism is started when the thermoelectrical 
starting mechanism BAE 72B-S is activated, when a reset button on BAE 72B-S is pushed or 
when a power supply of the actuating mechanism is stopped.

1.4.  

The damper is sealed with a silicon packing against smoke penetration after closing the blade. At

 

the same time, the damper blade is bedded in a material which enlarges its capacity and air

 

proofs the air duct.

1.5.  

Operation of the dampers does not depend on the direction of air circulation. The dampers can

 

be located in an arbitrary position.

1.6.  

Dampers have one inspection hole, since the shutting device and the inspection hole can be set 
into  the  most  advantageous  position  (with  respect  to  the  operation  and  manipulation  with  the 
control device).

1.7.  

Exact damper function is provided under the following conditions:

 

  

a) Maximum air circulation speed: 12 m.s

-1

 

  

Maximum pressure difference: 1500 Pa

 

  

b) Dampers could be displaced into position “CLOSED” only in case that ventilator, or Air 

  

  Handling  Unit  is  switched  off.  The  goal  is  the  securing  of  proper  closing  and  safe 

  

  function of Fire Damper in case of Fire.

 

  

 

  

c) The  air circulation in  the whole damper section  must be  secured as steady on  whole 

  

  surface.

1.8.  

Dampers are designed for macroclimatic areas with mild climate according to EN 60 721-3-3.

1.9.  

Dampers are suitable for systems without abrasive, chemical and adhesive particles.

1.10.  

Temperature in the place of installation is permitted to range from - 20°C to + 50°C.

1.12.  

In this document are used next signs and units.

1.11.  

If is not noticed other way, all dimensions and weight are in millimeters and kilograms.

Key :

w

[m.s

-1

]

air velocity

  p

[Pa]

pressure loss

L

w

[dB]

level of acoustic output

[ ]

pressure loss coefficient

[kg.m

-3

]

density

D

[mm]

dimension

[m

2

]

area

Содержание alnor FDMD






















Отзывы: