Man E0834 LE302 Скачать руководство пользователя страница 62

Страница: 62 / 90

Faults

Carefully read the Operating Instructions before starting any work!

This is especially valid for the chapter on General Safety Instructions

and the safety instructions in each of the chapters.

Fault

Remedy

Possible cause

Poor performance

Air filter clogged

Exhaust pipe clogged

Air intake pipe leaks

Charge mixture cooler dirty/leaks

Charge mixture ducting leaks

Turbocharger leaks, faulty, dirty

Insufficient compression in cylinder or
more than 3-4 bar pressure difference
between the cylinders

Remedy from manufacturer ser
vice

Coolant temperature
too high, loss of coolant

Coolant level too low

Air in coolant circuit

Radiator very dirty, fins clogged

V-belt for coolant pump not correctly
tightened (slips)

Cap with work valves on expansion
reservoir/radiator is faulty or leaks

Temperature display faulty

Coolant pump leaks, defective (bearing
damage)

Thermostat faulty, does not open

Coolant lines leak, clogged or twisted

Remedy from manufacturer ser
vice

Lube-oil pressure too
low

Oil level in oil pan too low

Engine temperature to high

Oil pressure indicator faulty

Selected oil viscosity is inappropriate for
ambient temperature (too thin)

Oil in oil pan is too thin (contains con
densation)

Bearing heavily worn

Oil pump gears heavily worn

Safety valve in oil circuit faulty (does not
close, spring is worn or broken)

See "Fluids and Lubricants..."

Remedy from manufacturer ser
vice

Lube-oil pressure too
high

Engine cold

Selected oil viscosity is inappropriate for
ambient temperature (too thick)

Oil pressure indicator faulty

Safety valve in oil circuit faulty (does not
open)

Oil lines/oil ducts clogged

See "Fluids and Lubricants..."

Remedy from manufacturer ser
vice

Содержание E0834 LE302



























































































Результаты поиска

Содержание E0834 LE302

Отзывы:

Похожие инструкции для E0834 LE302

Бренды по названию

Популярные бренды

Man E0834 LE302, Руководство по эксплуатации

Результаты поиска

Содержание E0834 LE302

Отзывы:

Похожие инструкции для E0834 LE302

Бренды по названию

Популярные бренды