background image

General Safety Instructions

15

Carefully read the Operating Instructions before starting any work!
This is especially valid for the chapter on General Safety Instructions 
and the safety instructions in each of the chapters.

2.5

Personnel Requirements

2.5.1

Qualifications

WARNING!

Risk of injury caused by insufficient qualifications!

Improper handling can result in significant personal injury and property damage

For this reason:

S

Specific activities must only be performed by those persons who are named in the re­
spective chapters in these Operating Instructions.

The following qualifications will be designated in the Operating Instructions for various task areas.

S

Instructed Persons 

Have been instructed in a briefing about the possible dangers of improper handling in their tasks.

S

Qualified Personnel

Due to their technical training, knowledge and experience and knowledge of the relevant regulations
they can properly perform the tasks assigned to them.

S

Electric Specialist

Is capable of performing work on electrical systems due to his/her technical education/training, know­
ledge and experiences as well as knowledge of the respective standards and regulations and can recog­
nise and avoid any possible dangers.
The electric specialist is trained for the specific operating site in which he/she works and knows the rel­
evant standards and regulations.

Only those people who can perform their work reliably should be considered as authorised personnel. Indi­
viduals whose responsiveness is influenced, for example, by alcohol or drugs, are not permitted.

S

When selecting personnel, observe the regulations regarding age and profession valid at the operating
site.

2.5.2

Unauthorised Persons

WARNING!

Danger for unauthorised persons!

Unauthorised persons who do not fulfil the requirements described here do not realise the
dangers that exist in the working area.

For this reason:

S

Keep unauthorised persons out of the working area.

S

In case of doubt, address the person and remove him/her from the working area if neces­
sary.

S

Interrupt the work until all unauthorised persons are out of the working area.

2.5.3

Instructions

Personnel must be instructed on regular basis and this should be documented in a log to keep better track
of who and when.

Содержание E0834 LE302



























































































Отзывы: