background image

Safety regulations

7

D

When working on the electrical system, first disconnect the earth cable of the battery
and reconnect this last to prevent short circuits.

D

Follow the manufacturer’s instructions for handling batteries.

Caution:

Accumulator acid is toxic and caustic. Battery gases are explosive.

D

When performing welding work, observe the “Notes for welders”.

2. Regulations designed to prevent damage to engine and premature wear

D

The engine must be cleaned thoroughly prior to repair. Ensure that dirt, sand or foreign matter
will not get into the engine during repair work.

D

If engine operation is disrupted, immediately determine the cause and have it remedied to prevent addi-
tional damage.

D

Always use genuine MAN parts only.Installation of “equally” good parts from other suppliers may cause
severe damage for which the workshop carrying out the work is responsible.

D

Never allow the engine to run dry, i.e. without lubricant or coolant. 

Appropriate notices must be attached to engines that are not ready for operation.

D

Use only MAN-approved service products (fuel, engine oil, anti-freeze and anti-corrosion agent). Pay
attention to cleanliness. Diesel fuel must be free of water.

D

Do not fill engine oil beyond the max. notch on the dipstick. Do not exceed the maximum per-
missible tilt of the engine.

Serious damage to the engine may result if these instructions are not adhered to.

D

Control and monitoring devices (charge control, oil pressure, coolant temperature) must be in perfect
working order.

D

Observe the instructions for operating the alternator; see chapter “Maintenance and care” in the Oper-
ator’s Manual.

3. Regulations designed to prevent pollution

Engine oil and filter cartridges and elements, fuel / fuel filters

D

Old oil must be passed on for recycling.

D

Take strict precautions to ensure that no oil or Diesel fuel gets into the drains or the ground.

Caution:

The drinking water supply could be contaminated.

D

Filter elements are classed as dangerous waste and must be treated as such.

Coolant

D

Treat undiluted corrosion protection agents and / or antifreeze as hazardous waste.

Содержание D 2876 LE 201

















Отзывы: