MALONE
R
Installation & Loading Instructions - MPG106M (MD) AutoLoader
5
. Confirm the carriers are in alignment.
Firmly tighten the T-knobs until both
carriers are securely fixed to the cross
bars. See image 5.
. Insert a second Mounting Bolt into the top
side unused hex hole and down through the
Jawz mounting adapter. Apply a second
T-knob and slightly tighten until the carrier
is secure. Repeat steps 1-4 for the 2nd
carrier and rear cross bar. See image 4.
. Insert the four Rubber Plugs into the four
top side hex holes in the two carriers. See
image 6.
Step 2: Loading the Kayak
. Route the free end of a 12’ Load Strap
through the rear of the top strap slot in
the top of the carrier. Pull the free end
down until there is an even loop. Repeat
for the second carrier. See image 7.
TM
4
6
7
MALONE
R
. Insert a second Mounting Bolt into the top side unused hex
hole and down through the Jawz mounting adapter. Apply
washer and second T-knob and slightly tighten until the carrier
is secure. Repeat steps 1-4 for the 2nd carrier and rear cross
bar. See image 4.
. Insérez un boulon de fixation dans le second trou hexagonal
situé sur le côté supérieur du support et faites-le passer dans
l’adaptateur Jawz. Vissez un bouton en T à la base du second
boulon, puis serrez légèrement jusqu’à ce que le support soit
bien fixé. Répétez les étapes 1 à 4 pour le deuxième support
et la barre transversale arrière. (Figure 4)
Installation & Loading Instructions - MPG117MD J-Pro2
Instructions - Installation et chargement
TM
. Route the free end of a 12’ Load Strap around the
top rear of the carrier. Pull the free end down until
there is an even loop. Repeat for the second carrier.
See image 7.
. Faites passer le bout plat d’une des courroies de fixation
de 3,6 mètres autour de la partie supérieure du support
arrière.Tirez sur le bout plat de la courroie afin d’obtenir
une boucle de longueurs égales. Faites de même pour le
deuxième support. (Figure 7)
. Confirm the carriers are in alignment. Firmly tighten
the T-knobs until both carriers are securely fixed to
the cross bars. See image 5.
. Assurez-vous que les supports soient bien alignés.
Vissez fermement les boutons en ‘‘T’’ jusqu’à ce que
les deux supports soient solidement fixés aux barres
transversales. (Figure 5)
5
. Insert the four Rubber Plugs into the four top side hex holes
in the two carriers. See image 6.
. Insérez un bouchon de caoutchouc dans chacun des quatre
trous hexagonaux situés sur le côté supérieur des supports.
(Figure 6)
4
6
7
MALONE
R
Installation & Loading Instructions - MPG106M (MD) AutoLoader
5
. Confirm the carriers are in alignment.
Firmly tighten the T-knobs until both
carriers are securely fixed to the cross
bars. See image 5.
. Insert a second Mounting Bolt into the top
side unused hex hole and down through the
Jawz mounting adapter. Apply a second
T-knob and slightly tighten until the carrier
is secure. Repeat steps 1-4 for the 2nd
carrier and rear cross bar. See image 4.
. Insert the four Rubber Plugs into the four
top side hex holes in the two carriers. See
image 6.
Step 2: Loading the Kayak
. Route the free end of a 12’ Load Strap
through the rear of the top strap slot in
the top of the carrier. Pull the free end
down until there is an even loop. Repeat
for the second carrier. See image 7.
TM
4
6
7
4
MALONE
R
Installation & Loading Instructions - MPG106M (MD) AutoLoader
5
. Confirm the carriers are in alignment.
Firmly tighten the T-knobs until both
carriers are securely fixed to the cross
bars. See image 5.
. Insert a second Mounting Bolt into the top
side unused hex hole and down through the
Jawz mounting adapter. Apply a second
T-knob and slightly tighten until the carrier
is secure. Repeat steps 1-4 for the 2nd
carrier and rear cross bar. See image 4.
. Insert the four Rubber Plugs into the four
top side hex holes in the two carriers. See
image 6.
Step 2: Loading the Kayak
. Route the free end of a 12’ Load Strap
through the rear of the top strap slot in
the top of the carrier. Pull the free end
down until there is an even loop. Repeat
for the second carrier. See image 7.
TM
4
6
7
MALONE
R
Installation & Loading Instructions - MPG106M (MD) AutoLoader
5
. Confirm the carriers are in alignment.
Firmly tighten the T-knobs until both
carriers are securely fixed to the cross
bars. See image 5.
. Insert a second Mounting Bolt into the top
side unused hex hole and down through the
Jawz mounting adapter. Apply a second
T-knob and slightly tighten until the carrier
is secure. Repeat steps 1-4 for the 2nd
carrier and rear cross bar. See image 4.
. Insert the four Rubber Plugs into the four
top side hex holes in the two carriers. See
image 6.
Step 2: Loading the Kayak
. Route the free end of a 12’ Load Strap
through the rear of the top strap slot in
the top of the carrier. Pull the free end
down until there is an even loop. Repeat
for the second carrier. See image 7.
TM
4
6
7
MALONE
R
. Insert a second Mounting Bolt into the top side unused hex
hole and down through the Jawz mounting adapter. Apply
a second T-knob and slightly tighten until the carrier is
secure. Repeat steps 1-4 for the 2nd carrier and rear cross
bar. See image 4.
. Insérez un boulon de fixation dans le second trou hexagonal
situé sur le côté supérieur du support et faites-le passer dans
l’adaptateur Jawz. Vissez un bouton en T à la base du second
boulon, puis serrez légèrement jusqu’à ce que le support soit
bien fixé. Répétez les étapes 1 à 4 pour le deuxième support
et la barre transversale arrière. (Figure 4)
Installation & Loading Instructions - MPG118MD J-Loader
Instructions - Installation et chargement
TM
. Route the free end of a 12’ Load Strap around the
top rear of the carrier. Pull the free end down until
there is an even loop. Repeat for the second carrier.
See image 7.
. Faites passer le bout plat d’une des courroies de fixation
de 3,6 mètres autour de la partie supérieure du support
arrière.Tirez sur le bout plat de la courroie afin d’obtenir
une boucle de longueurs égales. Faites de même pour le
deuxième support. (Figure 7)
. Confirm the carriers are in alignment. Firmly tighten
the T-knobs until both carriers are securely fixed to
the cross bars. See image 5.
. Assurez-vous que les supports soient bien alignés.
Vissez fermement les boutons en ‘‘T’’ jusqu’à ce que
les deux supports soient solidement fixés aux barres
transversales. (Figure 5)
5
. Insert the four Rubber Plugs into the four top side hex holes
in the two carriers. See image 6.
. Insérez un bouchon de caoutchouc dans chacun des quatre
trous hexagonaux situés sur le côté supérieur des supports.
(Figure 6)
4
6
7
. With the carriers in the UP position. Gently push down
on the release pins. They will automatically stop, lock
in place, and remain fixed. See image 6.
. Lorsque les supports sont relevés, appuyez doucement
sur la goupille de verrouillage. Elle se bloquera
automatiquement et sera ainsi verrouillée. (Figure 6)
. With the carriers in the DOWN position. Gently pull up
on the release pins. Lift and rotate the rear of the carrier
until it stops in the UP position. See image 5.
. Lorsque les supports sont rabaissés, tirez doucement la
goupille de verrouillage vers le haut. Soulevez la partie
arrière du support jusqu’à ce que celui-ci se bloque en
position relevée. (Figure 5)
5
4
6
2
MALONE
R
. Insert a second Mounting Bolt into the top side unused
hex hole and down through the Jawz mounting adapter.
Close the mounting hole cover. Apply a washer and second
T-knob and slightly tighten until the carrier is secure.
Repeat steps 1-4 for the 2nd carrier and rear cross bar.
See image 4.
. Insérez un boulon de fixation dans le second trou hexagonal
situé sur le côté supérieur du support et faites-le passer
dans l’adaptateur Jawz. Vissez un bouton en T à la base du
second boulon, puis serrez légèrement jusqu’à ce que le
support soit bien fixé. Répétez les étapes 1 à 4 pour le
deuxième support et la barre transversale arrière.
(Figure 4)
Installation & Loading Instructions - MPG114MD DownLoader
Instructions - Installation et chargement
TM
