manualshive.com logo in svg

Malaguti 500 cc 4T, Руководство по обслуживанию, Страница: 47 / 78

Поделиться
Скачать
Malaguti 500 cc 4T Скачать руководство пользователя страница 47

46

10/07

Inspecting the piston
rings

- Alternately insert the three sealing
rings into the cylinder, in the area where
it retains its original diameter. Using the
piston, insert the rings perpendicularly
to the cylinder axis.

- Make sure that each single sealing
ring evenly adheres to the cylinder liner.
If it does not, this means the ring is
worn. Replace it.

- Measure the opening (see figure) of
the sealing rings using a feeler gauge.

- If higher values than those prescribed
are measured, replace the linings.

Check the size of the sealing ring
opening:

Compression ring: 0.15 ÷ 0.35 mm.
Max. value 0.5 mm

Oil scraper ring: 0.25 ÷ 0.50 mm.
Max. value 0.65 mm

Oil scraper ring: 0.25 ÷ 0.50 mm.
Max. value 0.65 mm

Rings/housing coupling clearances:

Carefully clean the sealing ring
housings.

Place a thickness gauge between the
ring and the housing as shown in the
drawing and check the coupling
clearances.

Top ring
Standard coupling
clearance:0.01÷0.06 mm

Maximum clearances allowed after
use: 0.10 mm

Intermediate ring
Standard coupling
clearance:0.02÷0.07 mm

Maximum clearances allowed after
use: 0.10 mm

Oil scraper ring
Standard coupling
clearance:0.01÷0.06 mm

Maximum clearances allowed after
use: 0.10 mm

Replace the piston if clearances exceed
the maximum limits specified in the
table.

Содержание 500 cc 4T















































































Отзывы:

Нет отзывов