Maktec MT902 Скачать руководство пользователя страница 6

6

7.

Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for loose
or cracked wires. If power tool or accessory is
dropped, inspect for damage or install an
undamaged accessory. After inspecting and
installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum
no-load speed for one minute. 

Damaged accesso-

ries will normally break apart during this test time.

8.

Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
workpiece fragments. 

The eye protection must be

capable of stopping flying debris generated by vari-
ous operations. The dust mask or respirator must be
capable of filtrating particles generated by your oper-
ation. Prolonged exposure to high intensity noise
may cause hearing loss.

9.

Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.

 Fragments of

workpiece or of a broken accessory may fly away
and cause injury beyond immediate area of opera-
tion.

10. Hold power tool by insulated gripping surfaces

only, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord. 

Cutting accessory contacting a “live”

wire may make exposed metal parts of the power
tool “live” and shock the operator.

11. Position the cord clear of the spinning acces-

sory. 

If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled into
the spinning accessory.

12. Never lay the power tool down until the acces-

sory has come to a complete stop. 

The spinning

accessory may grab the surface and pull the power
tool out of your control.

13. Do not run the power tool while carrying it at

your side. 

Accidental contact with the spinning

accessory could snag your clothing, pulling the
accessory into your body.

14. Regularly clean the power tool’s air vents. 

The

motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may
cause electrical hazards.

15. Do not operate the power tool near flammable

materials. 

Sparks could ignite these materials. 

16. Do not use accessories that require liquid cool-

ants. 

Using water or other liquid coolants may result

in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other acces-
sory. Pinching or snagging causes rapid stalling of the
rotating accessory which in turn causes the uncontrolled
power tool to be forced in the direction opposite of the
accessory’s rotation at the point of the binding. 
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the mate-
rial causing the wheel to climb out or kick out. The wheel
may either jump toward or away from the operator,
depending on direction of the wheel’s movement at the
point of pinching. Abrasive wheels may also break under
these conditions.
Kickback is the result of power tool misuse and/or incor-
rect operating procedures or conditions and can be
avoided by taking proper precautions as given below. 

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control
over kickback or torque reaction during start-
up. 

The operator can control torque reactions or

kickback forces, if proper precautions are taken. 

b)

 

Never place your hand near the rotating

accessory. 

Accessory may kickback over your

hand. 

c) Do not position your body in the area where

power tool will move if kickback occurs. 

Kick-

back will propel the tool in direction opposite to
the wheel’s movement at the point of snagging. 

d)

 

Use special care when working corners,
sharp edges etc. Avoid bouncing and snag-
ging the accessory. 

Corners, sharp edges or

bouncing have a tendency to snag the rotating
accessory and cause loss of control or kickback. 

e) Do not attach a saw chain woodcarving blade

or toothed saw blade. 

Such blades create fre-

quent kickback and loss of control. 

Safety Warnings Specific for Grinding and Abrasive
Cutting-Off Operations: 

a) Use only wheel types that are recommended

for your power tool and the specific guard
designed for the selected wheel. 

Wheels for

which the power tool was not designed cannot
be adequately guarded and are unsafe. 

b) The guard must be securely attached to the

power tool and positioned for maximum
safety, so the least amount of wheel is
exposed towards the operator. 

The guard

helps to protect operator from broken wheel frag-
ments and accidental contact with wheel. 

c) Wheels must be used only for recommended

applications. For example: do not grind with
the side of cut-off wheel. 

Abrasive cut-off

wheels are intended for peripheral grinding, side
forces applied to these wheels may cause them
to shatter. 

d)  Always use undamaged wheel flanges that

are of correct size and shape for your
selected wheel. 

Proper wheel flanges support

the wheel thus reducing the possibility of wheel
breakage. Flanges for cut-off wheels may be dif-
ferent from grinding wheel flanges. 

Содержание MT902





































































Отзывы: