Maktec MT070 Скачать руководство пользователя страница 5

FUNCTIONAL DESCRIPTION 

 

CAUTION: 

• 

Always be sure that the tool is switched off and the 
battery cartridge is removed before adjusting or 
checking function on the tool. 

Installing or removing battery cartridge 

Fig.1 

• 

Always switch off the tool before installing or 
removing of the battery cartridge. 

• 

To remove the battery cartridge, slide it from the tool 
while sliding the button on the front of the cartridge. 

• 

To install the battery cartridge, align the tongue on the 
battery cartridge with the groove in the housing and 
slip it into place. Always insert it all the way until it 
locks in place with a little click. If you can see the red 
indicator on the upper side of the button, it is not 
locked completely. Install it fully until the red indicator 
cannot be seen. If not, it may accidentally fall out of 
the tool, causing injury to you or someone around you. 

• 

Do not use force when installing the battery 
cartridge. If the cartridge does not slide in easily, it 
is not being inserted correctly. 

Battery protection system 

The battery cartridge is equipped with the protection 
system, which automatically cuts off the output power 
for its long service life. 
The tool stops during operation when the tool and/or 
battery are placed under the following situation. This is 
caused by the activation of protection system and does 
not show the tool trouble. 

• 

When the tool is overloaded: 

At this time, release the switch trigger, 
remove the battery cartridge and remove 
causes of overload and then pull the switch 
trigger again to restart. 

• 

When battery cells get hot: 

If any operation of the switch trigger, the 
motor will remain stopped. At this time, stop 
use of the tool and cool the battery cartridge. 

• 

When the remaining battery capacity gets low: 

If you pull the switch trigger, the motor runs 
again but stops soon. In this case, to prevent 
over discharge, remove the battery cartridge 
from the tool and charge it. 

Switch action 

Fig.2 

CAUTION: 

• 

Before inserting the battery cartridge into the tool, 
always check to see that the switch trigger 
actuates properly and returns to the "OFF" 
position when released. 

 
 

To start the tool, simply pull the switch trigger. Tool 
speed is increased by increasing pressure on the switch 
trigger. Release the switch trigger to stop. 

Reversing switch action 

Fig.3 

This tool has a reversing switch to change the direction 
of rotation. Depress the reversing switch lever from the 
A side for clockwise rotation or from the B side for 
counterclockwise rotation. 
When the reversing switch lever is in the neutral 
position, the switch trigger cannot be pulled. 

 

CAUTION: 

• 

Always check the direction of rotation before 
operation. 

• 

Use the reversing switch only after the tool comes 
to a complete stop. Changing the direction of 
rotation before the tool stops may damage the tool. 

• 

When not operating the tool, always set the 
reversing switch lever to the neutral position. 

Speed change 

Fig.4 

To change the speed, first switch off the tool and then 
slide the speed change lever to the "2" side for high 
speed or "1" side for low speed. Be sure that the speed 
change lever is set to the correct position before 
operation. Use the right speed for your job. 

 

CAUTION: 

• 

Always set the speed change lever fully to the 
correct position. If you operate the tool with the 
speed change lever positioned halfway between 
the "1" side and "2" side, the tool may be 
damaged. 

• 

Do not use the speed change lever while the tool 
is running. The tool may be damaged. 

Adjusting the fastening torque 

Fig.5 

The fastening torque can be adjusted in 17 steps by 
turning the adjusting ring so that its graduations are 
aligned with the pointer on the tool body. The fastening 
torque is minimum when the number 1 is aligned with 
the pointer, and maximum when the 

 marking  is 

aligned with the pointer. 
The clutch will slip at various torque levels when set at 
the number 1 to 16. The clutch is designed not to slip at 
the

marking. 

Before actual operation, drive a trial screw into your 
material or a piece of duplicate material to determine 
which torque level is required for a particular application. 

 
 

Содержание MT070





















































Отзывы: