Makita UX01G, Инструкция по эксплуатации

Страница: 14 / 136

14 ENGLISH
Overload protection
If the tool or battery gets into one of the following situa-
tion, the tool automatically stops and the caution lamp
starts blinking in green:
— The tool is overloaded by entangled weeds or other debris.
— The cutting tool is locked or kicked back.
— The main power button is turned on while the
switch trigger is being pulled.
In this situation, release the switch trigger and remove
entangled weeds or debris if necessary. After that, pull
the switch trigger again to resume.
CAUTION:
If you need to remove the entan -
gled weeds on the tool or release the locked
cutting tool, be sure to turn the tool off before you
start.
Overheat protection for tool or battery
If the tool or battery cartridge is overheated, the tool stops
automatically. When the tool is overheated, the caution
lamp lights up in red. When the battery cartridge is over-
heated, the caution lamp blinks in red. Let the tool and/or
battery cool down before turning the tool on again.
Overdischarge protection
When the battery capacity becomes low, the tool stops
automatically and the caution lamp starts blinking in red.
If the tool does not operate even when the switches are oper-
ated, remove the battery cartridge from the tool and charge it.
Indicating the remaining battery capacity
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
► Fig.7: 1. Indicator lamps 2. Check button
Indicator lamps Remaining
capacity
Lighted Off Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery
may have
malfunctioned.
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
NOTE: The first (far left) indicator lamp will blink when
the battery protection system works.
Main power switch
WARNING:
Always turn off the main power
switch when not in use.
Press the main power button to turn on the tool. To turn
off the tool, press and hold the main power button until
the speed indicators go off.
► Fig.8: 1. Main power button
NOTE: The caution lamp brinks if the switch trigger
is pulled under unoperatable conditions. The caution
lamp blinks if you turn on the main power switch while
holding down the lock-off lever and the switch trigger.
NOTE: This tool employs the auto power-off function.
To avoid unintentional start up, the main power switch
will automatically shut down when the switch trigger
is not pulled for a certain period after the main power
switch is turned on.
Switch action
WARNING:
For your safety, this tool is
equipped with lock-off lever which prevents the
tool from unintended starting. NEVER use the tool
if it runs when you simply pull the switch trigger
without pressing the lock-off lever. Return the
tool to our authorized service center for proper
repairs BEFORE further usage.
WARNING:
NEVER tape down or defeat pur -
pose and function of lock-off lever.
CAUTION:
Before installing the battery car -
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
CAUTION:
Never put your finger on the main
power button and switch trigger when carrying
the tool. The tool may start unintentionally and cause
injury.
NOTICE:
Do not pull the switch trigger hard with -
out pressing the lock-off lever. This can cause
switch breakage.
To prevent the switch trigger from being accidentally
pulled, a lock-off lever is provided.
► Fig.9: 1. Lock-off lever 2. Switch trigger
To start the tool, turn on the main power switch and
grasp the handle (the lock-off lever is released by the
grasp) and then pull the switch trigger. Tool speed is
increased by increasing the pressure on the switch
trigger. To stop the tool, release the switch trigger.