24 ENGLISH
MAINTENANCE
WARNING:
Always be sure that the tool is
switched off and battery cartridge is removed
before attempting to perform inspection or
maintenance on the tool.
Failure to switch off and
remove the battery cartridge may result in serious
personal injury
from
accidental start-up.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs,
any
other
maintenance
or
adjustment should
be performed by
Makita Authorized or Factory Service Centers, always
using Makita replacement parts.
Replacing the nylon cord
Clean the tool by wiping off dust, dirt, or cut off grass
with a dry cloth or one dipped in soapy water and wrung
out. If the cut off grass is adhered to the motor housing,
be sure to remove it.
►
Fig.28:
1.
Motor housing
Storage
The hole in the handle is convenient for hanging the tool
from a nail or screw on the wall. Before storing the tool,
raise the wire guard, shorten the shaft, and then fold the
front grip.
►
Fig.29:
1.
Wire guard
►
Fig.30:
1.
Front grip
2.
Shaft
►
Fig.31:
1.
Hole
WARNING:
Use nylon cord with diameter specified in “SPECIFICATIONS” only. Never use heavier line,
metal wire, rope or the like.
Use recommended nylon cord only, otherwise it may cause damage to the tool and
result
in
serious
personal
injury.
WARNING:
Make sure that the cover of the nylon cutting head is secured to the housing properly as
described below.
Failure
to
properly
secure
the
cover
may
cause
the
nylon
cutting
head
to
fly
apart
resulting
in
serious
personal
injury.
Replace the nylon cord if the cord is not feeding any more.
►
Fig.32:
(1)
Up to 8 m
(2)
70 - 80 mm
TROUBLESHOOTING
Before
asking
for
repairs,
conduct
your
own
inspection first.
If
you
find
a
problem
that
is
not
explained in
the
manual,
do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using
Makita replacement parts for repairs.
State of abnormality
Probable cause (malfunction)
Remedy
Motor does not run.
Battery cartridge is not installed.
Install the battery cartridge.
Battery problem (under voltage)
Recharge the battery. If recharging is not effective,
replace battery.
The drive system does not work
correctly.
Ask your local authorized service center for repair.
Motor stops running after a little use.
Battery's charge level is low.
Recharge the battery. If recharging is not effective,
replace battery.
Overheating.
Stop using of tool to allow it to cool down.
It does not reach maximum RPM.
Battery is installed improperly.
Install the battery cartridge as described in this
manual.
Battery power is dropping.
Recharge the battery. If recharging is not effective,
replace battery.
Detaching the shoulder harness
Cleaning the tool
Содержание UR100D
