22 ENGLISH
hold
the
handle when lowering your
right hand.
►
Fig.10:
1.
Handle
To
adjust
the
shaft
length,
open
the
lock
lever,
then
adjust
the
length
of
the
shaft,
and
then
close
the
lock
lever.
►
Fig.11:
1.
Lock lever
Adjust
the
position
of
the
front
grip
so
that
you
can
hold
the front grip when lowering your
left hand.
►
Fig.12:
1.
Front grip
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
Never start the tool unless it is
completely assembled.
Operation of the tool in a
partially assembled state may result in serious
personal
injury
from
accidental start-
up.
Installing the front grip
Attach the front grip to the front grip holder and secure it
with a hex bolt and the thumb nut as shown in the
figure.
►
Fig.13:
1.
Front grip
2.
Thumb nut
3.
Hex
bolt
The
front
grip
angle
is
adjustable. To
adjust
the
front
grip angle, loosen the thumb nut, set the front grip at an
proper angle according to your work and then tighten
the
thumb
nut
clockwise firmly.
Installing the wire guard
NOTICE:
Do not expand the wire guard outward
too much. Otherwise it may break.
►
Fig.14
To
reduce
the
risk
of
damaging the
objects
in
front
of
the
cutting head, attach the wire
guard to the protector so that it controls the cutting
range.
Slightly expand the wire guard outward and then insert it
into the holes of the protector.
Attach the wire guard to the holes on the front side of
the protector. The nylon cord mark on the protector
indicates the hole to be used.
►
Fig.15:
1.
Hole
When wire guard is not in use, lift it for the idle position.
►
Fig.16:
1.
Wire guard
Installing the protector
CAUTION:
While installing the protector, be
careful not to contact the nylon cord cutter on
the protector.
Contact with the cutter could result in
personal
injury.
►
Fig.17:
1.
Screw
2.
Protector
Mount
the
protector by
fitting
it
on
to
the
motor
housing,
and then secure it with two screws.
Installing nylon cutting head
Optional accessory
CAUTION:
If the nylon cutting head
accidentally impacts a rock or hard object during
operation, stop the tool and inspect for any
damage. If the nylon cutting head is damaged,
replace it immediately.
Use of a damaged cutting
tool could result
in
serious
personal
injury.
CAUTION:
Be sure to remove the hex wrench
after installation.
CAUTION:
When installing or removing the
nylon cutting head, be careful not to contact the
nylon cord cutter on the protector.
Contact with the
cutter
may
result
in
personal
injury.
NOTICE:
Be sure to use genuine Makita nylon
cutting head.
1.
Turn the tool upside down so that you can replace
the cutting tool easily.
2.
Insert the hex wrench through the hole on the
motor housing and rotate the spindle until the
spindle is locked.
►
Fig.18:
1.
Hex
wrench
2.
Hole
3.
Spindle
3.
Place the nylon cutting head onto the spindle and
tighten it by turning it clockwise.
►
Fig.19:
1.
Nylon cutting head
4.
Remove the hex wrench.
To remove the nylon cutting head, turn it
counterclockwise while locking the spindle with the hex
wrench.
Содержание UR100D
