24 ENGLISH
When using a nylon cutting head (bump & feed
type)
The nylon cutting head is a dual string trimmer head
provided with a bump & feed mechanism.
To feed out the nylon cord, tap the cutting head against
the ground while rotating.
►
Fig.35:
1.
Most effective cutting area
NOTICE:
The bump feed will not operate prop-
erly if the nylon cutting head is not rotating.
NOTE:
If the nylon cord does not feed out while
tapping the head, rewind/replace the nylon cord
by following the procedures in the section for the
maintenance.
Chisel blade
CAUTION:
Never cut trees larger than 70 mm
diameter.
The chisel blade is useful for cutting shrubs and trees.
To avoid kickback, always apply the segment of the
chisel blade between 8 and 11 o’clock to a tree.
►
Fig.36:
1.
8 to 11 o’clock segment of the blade
For ease of cutting a tree, support the protector against
the tree stem as illustrated.
►
Fig.37
Shredder blade
CAUTION:
Never raise the tool head higher
than your waist height.
CAUTION:
Never perform up-and-down
stroke with the cutting tool other than the shred-
der blade.
Shredder blade is useful for cutting open a dense bush
and shredding grass. Swing the tool head up and down,
or left and right onto the bush.
►
Fig.38
►
Fig.39
MAINTENANCE
WARNING:
Always be sure that the tool is
switched off and battery cartridge is removed
before attempting to perform inspection or main-
tenance on the tool.
Failure to switch off and remove
the battery cartridge may result in serious personal
injury from accidental start-up.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Replacing the nylon cord
WARNING:
Use only the nylon cord with
diameter specified in this instruction manual.
Never use heavier line, metal wire, rope or the
like.
Failure to do so may cause damage to the tool
and result in serious personal injury.
WARNING:
Always remove the nylon cutting
head from the tool when replacing the nylon cord.
WARNING:
Make sure that the cover of the
nylon cutting head is secured to the housing
properly as described below.
Failure to properly
secure the cover may cause the nylon cutting head to
fly apart resulting in serious personal injury.
Replace the nylon cord if it is not fed any more. The
method of replacing the nylon cord varies depending on
the type of the nylon cutting head.
B&F Z5L
►
Fig.40
121-M10L
►
Fig.41
Replacing the plastic blade
Replace the plastic blade if it is worn out or broken.
►
Fig.42
When installing the plastic blade, align the direction of
the arrow on the blade with that of the protector.
►
Fig.43:
1.
Arrow on the protector
2.
Arrow on the
blade
Storage
When storing the tool, loosen the knob and fold the
handle at a right angle. After that, tighten the knob.
►
Fig.44:
1.
Knob
2.
Handle
Содержание UR012GZ04
