![background image](http://html1.mh-extra.com/html/makita/up100d/up100d_instruction-manual_4035288011.webp)
11 ENGLISH
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
►
Fig.3:
1.
Indicator lamps
2.
Check button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
Indicator lamps
Remaining
capacity
Lighted
Off
75% to 100%
50% to 75%
25% to 50%
0% to 25%
NOTE:
Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts off power to the
motor to extend tool and battery life. The tool will auto-
matically stop during operation if the tool or battery is
placed under one of the following conditions:
Overloaded:
The tool is operated in a manner that causes it to draw
an abnormally high current. In this situation, turn the
tool off and stop the application that caused the tool to
become overloaded. Then turn the tool on to restart.
If the tool does not start, the battery is overheated. In this
situation, let the battery cool before turning the tool on again.
Low battery voltage:
The remaining battery capacity is too low and the tool
will not operate. If you turn the tool on, the motor runs
again but stops soon. In this situation, remove and
recharge the battery.
Indicator lamps
►
Fig.4:
1.
Indicator lamp (green)
2.
Indicator lamp
(red)
The meaning of indicator lamps is as follows:
(On:
Off:
Blinking: )
Green
Red
•
Green lamp lights up: the tool is turned on and
ready to operate.
Green
Red
•
Green lamp is blinking: the tool is turned on and in
the standby mode. To return to the normal mode,
pull the switch trigger twice.
Green
Red
•
Red lamp is blinking: the remaining battery capac-
ity is low.
Green
Red
•
Green lamp and red lamp light up: the tool or
battery is overheated, or the tool is overloaded, or
the battery runs out.
Green
Red
•
Red lamp lights up: An abnormality has occurred.
Turn off the tool, and then back on. If the abnor
-
mality persists, ask your local authorized service
center for repair.
Main power button
WARNING:
Always turn off the tool when not
in use.
To turn on the tool, press and hold the main power
button. The tool starts up in the standby mode and the
green indicator lamp blinks in green.
To turn off the tool, pull and hold the switch trigger more
than 3 seconds to close the shear blades, then release
the switch trigger, and then press the main power
button.
►
Fig.5:
1.
Main power button
2.
Switch trigger
NOTE:
This tool shifts to the standby mode when the
switch trigger is not pulled for a certain period after
the tool is turned on. When the green indicator lamp
is blinking, pull the switch trigger twice to return to the
normal mode.
NOTE:
This tool employs the auto power-off function.
To avoid unintentional start up, the tool automatically
shuts down when the switch trigger is not pulled for a
certain period after the tool is turned on.
Switch action
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
Turn on the tool, and pull the switch trigger twice to
open the upper shear blade. The green indicator lamp
lights up in green. When you pull the switch trigger, the
upper shear blade closes, and when you release the
switch trigger, the upper shear blade opens.
Содержание UP100D
