11 ENGLISH
NOTE:
Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Battery protection system
The tool is equipped with a battery protection system.
This system automatically cuts off power to the motor to
extend battery life.
The tool will automatically stop during operation if the
tool and/or battery are placed under one of the following
conditions:
Overloaded:
The tool is operated in a manner that causes it to draw
an abnormally high current.
In this situation, turn the tool off and stop the application
that caused the tool to become overloaded. Then turn
the tool on to restart.
If the tool does not start, the battery is overheated. In
this situation, let the battery cool before turning the tool
on again.
Low battery voltage:
The remaining battery capacity is too low and the tool
will not operate. If you turn the tool on, the motor runs
again but stops soon. In this situation, remove and
recharge the battery.
Switch action
WARNING:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the “OFF” position when released.
WARNING:
For your safety, this tool is
equipped with the lock-off button which prevents
the tool from unintended starting. Never use the
tool if it starts when you pull the switch trigger
without pressing the lock-off button.
Ask your local
Makita Service Center for repairs.
WARNING:
Never disable the lock function or
tape down the lock-off button.
NOTICE:
Do not pull the switch trigger forcibly
without pressing the lock-off button.
The switch
may break.
►
Fig.3:
1.
Switch trigger
2.
Lock-off button
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided.
To start the tool, press the lock-off button and pull the
switch trigger. Release the switch trigger to stop. The
lock-off button can be pressed from either the right or
left side.
Indicator lamp
The indicator lamp blinks or lights up when the remain
-
ing battery capacity is low or empty. The indicator lamp
also lights up when the tool becomes overloaded.
►
Fig.4:
1.
Indicator lamp
Lamp status and action to be taken
Indicator lamp
Status
Action to be taken
The lamp blinks
red.
The remaining
battery capacity
is low.
Charge the battery.
The lamp lights up
red. *
The tool has
stopped because
the remaining
battery capacity is
empty.
Charge the battery.
The tool has
stopped due to
overload.
Turn off the tool.
* The time at which the indicator lamp lights up varies depending
on the temperature around the work area and the battery car
-
tridge conditions.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
When replacing the shear blades,
always wear gloves so that your hands do not
directly contact the blades.
CAUTION:
When attaching or removing the
blade cover, always wear gloves to avoid touch-
ing the shear blades by accident.
NOTICE:
When replacing the shear blades, do
not wipe off grease from the gear and crank.
Installing or removing the shear
blades
CAUTION:
Attach the blade cover before
removing or installing the shear blades.
NOTICE:
If the parts other than the shear blades
such as the crank are worn out, ask Makita
Authorized Service Centers for parts replacement
or repairs.
1.
Place the tool upside down.
2.
Loosen 4 screws with a screwdriver, and then
remove the shear blades.
►
Fig.5:
1.
Screws
3.
Remove the crank from the shear blades.
►
Fig.6:
1.
Crank
NOTE:
The crank may remain in the tool.
Содержание UH353D
