Makita UC3520A, Инструкция по эксплуатации

Страница: 6 / 108

6
･
Caution: particular care and attention
required!
･
Caution: withdraw the mains plug
immediately if the cable is damaged!
･
Caution: kickback!
･
Protect against rain and damp!
･
Wear a helmet, goggles and ear
protection!
･
Wear safety gloves!
･
Withdraw the mains plug!
･
First aid
･
Recycling
･
CE marking
･
Maximum permissible length of cut
･
Direction of chain travel
･
Chain oil
･
Chain brake released/applied
･
Prohibited!
･
Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.
ENE031-1
Intended use
The tool is intended for cutting lumbers and logs.
ENF002-1
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
ENF100-1
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.35 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
ENH016-4
EC-DECLARATION OF CONFORMITY
The undersigned, Kato, as authorized by, declare that
the MAKITA machines,
Type:
211
EU model identification No.:
UC3020A, UC3520A, UC4020A:M6 05 10 24243 064
complies with the standard safety and health
requirements of the pertinent EU guidelines:
EU machinery guideline 98/37/EC, EU EMC guideline
2004/108/EC, Noise emission 2000/14/EG.
The requirements of the above EU guidelines were
implemented chiefly on the basis of the following
standards: EN60745-2-13, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3. The conformity
assessment procedure 2000/14/EG was performed per
Annex V. The measured sound power level (Lwa) is 100
dB(A). The guaranteed sound power level (Ld) is 101
dB(A). The EU Type-Examination per 98/37/EG was
performed by: TUV Product Service GmbH,
Zertifizierungsstelle, Ridlerstra e 31, D-80339 M nchen.
CE2007
000230
Tomoyasu Kato
Director
Responsible Manufacturer:
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
GEB037-3
Chain saw safety warnings:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to chain saw safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious
personal injury.
1. Keep all parts of the body away from the saw
chain when the chain saw is operating. Before
you start the chain saw, make sure the saw
chain is not contacting anything.
A moment of
inattention while operating chain saws may cause
entanglement of your clothing or body with the
saw chain.