![background image](http://html1.mh-extra.com/html/makita/tm3000cx1/tm3000cx1_instruction-manual_4720915005.webp)
5
ENGLISH
(Original instructions)
Explanation of general view
1
Slide switch
2
Dial
3
Application tool installation bolt
4
Holes in the application tool
5
Protrusions of the tool flange
6
Hex wrench
7
Tighten
8
Adapter
9
Joint
10 Nozzle band
11 Dust nozzle
12 Dust attachment
13 Felt ring
14 Pad
15 Protrusions
16 Holes
SPECIFICATIONS
• Due to our continuing programme of research and
development, the specifications herein are subject to
change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
ENE080-1
Intended use
The tool is intended for sawing and cutting wood, plastic,
gypsum, non-ferrous metals, and fastening elements (e.
g. unhardened nails and staples). It is also intended for
working soft wall tiles, as well as dry sanding and scrap-
ing of small surfaces. It is especially for working close to
edge and flush cutting.
GEA010-1
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
GEB096-3
MULTI TOOL SAFETY WARNINGS
1.
This power tool is intended to function for saw-
ing, cutting, grinding and sanding. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2.
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
3.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
4.
Position the cord clear of the spinning acces-
sory.
If you lose control, the cord may be cut or
snagged and your hand or arm may be pulled into
the spinning accessory.
5.
Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
6.
Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
7.
Hold the tool firmly.
8.
Make sure the application tool is not contacting
the workpiece before the switch is turned on.
9.
Keep hands away from moving parts.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11. Always switch off and wait for the blade to come
to a complete stop before removing the blade
from the workpiece.
12. Do not touch the application tool or the work-
piece immediately after operation; they may be
extremely hot and could burn your skin.
13. Do not operate the tool at no-load unnecessarily.
14. Always use the correct dust mask/respirator for
the material and application you are working
with.
15. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
16. This tool has not been waterproofed, so do not
use water on the workpiece surface.
17. Ventilate your work area adequately when you
perform sanding operations.
18. Use of this tool to sand some products, e.g.
leaded paint surfaces, wood and metals could
expose user and bystanders to dust containing
hazardous substances. Use appropriate respira-
tory protection.
Model
TM3000C
Oscillation per minute
6,000 – 20,000 (min
–1
)
Oscillation angle, left/right
1.6° (3.2° total)
Overall length
275 mm
Net weight
without dust extraction attachment
1.4 kg
with dust extraction attachment
1.5 kg
Safety class
/II
Содержание TM3000CX1
