![background image](http://html1.mh-extra.com/html/makita/rp1110/rp1110_instruction-manual_4016936005.webp)
5
ENGLISH
(Original instructions)
Explanation of general view
1
Adjusting knob
2
Stopper pole
3
Depth pointer
4
Stopper pole setting nut
5
Lock knob
6
Fast-feed button
7
Adjusting hex bolt
8
Stopper block
9
Nylon nut
10 Lock button
11 Switch trigger
12 Speed adjusting dial
13 Collet nut
14 Wrench
15 Shaft lock
16 Tighten
17 Loosen
18 Correct size collet cone
19 Workpiece
20 Bit revolving direction
21 Feed direction
22 View from the top of the tool
23 Straight guide
24 Lock screw
25 Guiding surface
26 Templet guide
27
Screw
28
Bit
29
Base
30
Templet
31
Workpiece
32
Distance (X)
33
Outside diameter of the templet
guide
34
Nozzle assembly
35
Dust nozzle assembly
36
Limit mark
37
Brush holder cap
38
Screwdriver
SPECIFICATIONS
Model
RP0910 RP1110C
Max. collet capacity ..................................................................... 8 mm or 1/4"
8 mm or 1/4"
Plunge capacity ........................................................................... 0 – 57 mm
0 – 57 mm
No load speed (min
–1
) ................................................................. 27,000
8,000 – 24,000
Overall height .............................................................................. 260 mm
260 mm
Net weight .................................................................................... 3.3 kg
3.4 kg
Safety class .................................................................................
/II
/II
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
ENE010-1
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
GEA010-1
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
GEB018-4
ROUTER SAFETY WARNINGS
1.
Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord.
Cutting a “live” wire may make exposed metal parts
of the power tool “live” and shock the operator.
2.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
3.
Wear hearing protection during extended period
of operation.
4.
Handle the bits very carefully.
5.
Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
6.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
7.
Hold the tool firmly with both hands.
8.
Keep hands away from rotating parts.
9.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
10. Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
11. Be careful of the bit rotating direction and the
feed direction.
12. Do not leave the tool running. Operate the tool
only when hand-held.
13. Always switch off and wait for the bit to come to
a complete stop before removing the tool from
workpiece.
14. Do not touch the bit immediately after operation;
it may be extremely hot and could burn your
skin.
15. Do not smear the tool base carelessly with thin-
ner, gasoline, oil or the like. They may cause
cracks in the tool base.
16. Use bits of the correct shank diameter suitable
for the speed of the tool.
17. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
18. Always use the correct dust mask/respirator for
the material and application you are working
with.
SAVE THESE INSTRUCTIONS.
Содержание RP1110
Страница 4: ...4 17 18 36 37 38 001145 005099 ...
Страница 50: ...50 ...
Страница 51: ...51 ...
Страница 52: ...Makita Corporation Anjo Aichi Japan www makita com 884320G995 IDE ...