Makita LXRH02 1 Series Скачать руководство пользователя страница 24

Страница: 24 / 25

BHR242, BHR243

Lead wires to Connector have to be routed

between Rib B and Rib D.

Lead wires to Connector and Stator lead wires

have to be routed between Rib A and Rib B.

Route the lead wires between Connector and Controller to the bottom of Housing L

so as not to rise on the top line of Rib C. Turn them back to set Connector in place.

Place the turned portion over the line extended from Rib D.

Do not put Stator lead wires on Rib C.

Rib D

Rib C

Rib B

Line extended from Rib D

iring diagram

Fig. D-3

Rib C

Rib D

Turned portion

Connector

Flag receptacles

Controller

Set Controller in place with Flag receptacles faced

as drawn above.

Rib A

Connector

Controller

The bottom of Housing L

viewed from the upper side

Terminal

Connect Lead wires to Controller/ Terminal

with Flag receptacles as drawn below.

Controller

Black

lead wire
Red

lead wire

Orange

lead wire

Black

lead wire
White

lead wire

Flag receptacles

Slacks of Lead wires between Controller and

Connector/ Stator have to be placed over the line

extended from Rib D.

Stator

Terminal

Do not put any lead

wires on this boss.

Содержание LXRH02 1 Series


























Результаты поиска

Содержание LXRH02 1 Series

Отзывы:

Похожие инструкции для LXRH02 1 Series

Бренды по названию

Популярные бренды

Makita LXRH02 1 Series, Техническая информация

Результаты поиска

Содержание LXRH02 1 Series

Отзывы:

Похожие инструкции для LXRH02 1 Series

Бренды по названию

Популярные бренды