background image

 

5-3

 

DISASSEMBLY/ASSEMBLY 

5-3-1

 

Armature 

5-3-1-1

 

Disassembling 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

5-3-2

 

Handle section 

5-3-2-1

 

Disassembling 

 
 
 
 
 
 
 
 
 
 
 
 

5-3-2-2

 

Assembling 

 
 

 

 
 
 
 
 
 
 
 
 

Fig. 1-1 

1)

 

Remove Carbon brush (45). 

2)

 

Unscrew seven M5×40 P.H. screws (34, 46) and 

remove Motor section with handle section from the 

main unit. 

Fig. 1-2 

3)

 

Pull out Armature (51) by hand. 

4)

 

Pull out Ball bearing (50, 54) with 1R269. 

 

 

 

 

Armature (51) 

Note: 

Be careful not to lose off 

Stopper (55).

 

Fig. 2-1 

1)

 

Unscrew four 4×18 Tapping screws (32) and three 

M5×40 P.H. Screws (34) and remove Handle L (30). 

Handle L (30) 

Fig. 2-2 

2)

 

Remove Power supply cord (40) and Switch (24) etc. 

Switch (24) 

Fig. 2-3 

1)

 

Set Switch lock (26), Switch lever (25) and 

Compression spring 4 (27) in place. 

Note:

 Fix Switch button 

(31) after Handle L (30) 

is installed. 

Compression 

spring 4 (27)   

Switch lock (26)   

Switch lever (25)   

 

Fig. 2-4 

2)

 

Press Switch button (31) into Handle L (31) with a 

click sound. 

Switch 

button (31) 

Handle L (31) 

Power supply cord (40) 

 

 

Makita Corporation   

 

 

 

5

 / 

15

 

Содержание LW1400
















Отзывы: