![background image](http://html1.mh-extra.com/html/makita/ls004gz/ls004gz_instruction-manual_4405950006.webp)
6
ENGLISH
12.
Provide adequate support such as table exten-
sions, saw horses, etc. for a workpiece that is
wider or longer than the table top.
Workpieces
longer or wider than the mitre saw table can tip
if not securely supported. If the cut-off piece or
workpiece tips, it can lift the lower guard or be
thrown by the spinning blade.
13.
Do not use another person as a substitute for
a table extension or as additional support.
Unstable support for the workpiece can cause the
blade to bind or the workpiece to shift during the
cutting operation pulling you and the helper into
the spinning blade.
14.
The cut-off piece must not be jammed or
pressed by any means against the spinning
saw blade.
If confined, i.e. using length stops, the
cut-off piece could get wedged against the blade
and thrown violently.
15.
Always use a clamp or a fixture designed to
properly support round material such as rods
or tubing.
Rods have a tendency to roll while
being cut, causing the blade to "bite" and pull the
work with your hand into the blade.
16.
Let the blade reach full speed before contact-
ing the workpiece.
This will reduce the risk of the
workpiece being thrown.
17.
If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving
parts to stop and disconnect the plug from
the power source and/or remove the battery
pack. Then work to free the jammed material.
Continued sawing with a jammed workpiece could
cause loss of control or damage to the mitre saw.
18.
After finishing the cut, release the switch, hold
the saw head down and wait for the blade to stop
before removing the cut-off piece.
Reaching with
your hand near the coasting blade is dangerous.
19.
Hold the handle firmly when making an incom
-
plete cut or when releasing the switch before
the saw head is completely in the down posi-
tion.
The braking action of the saw may cause
the saw head to be suddenly pulled downward,
causing a risk of injury.
20.
Only use the saw blade with the diameter that
is marked on the tool or specified in the man
-
ual.
Use of an incorrectly sized blade may affect
the proper guarding of the blade or guard opera-
tion which could result in serious personal injury.
21.
Only use the saw blades that are marked with
a speed equal or higher than the speed marked
on the tool.
22.
Do not use the saw to cut other than wood,
aluminum or similar materials.
23.
(For European countries only)
Always use the blade which conforms to
EN847-1.
Additional instructions
1.
Make workshop kid proof with padlocks.
2.
Never stand on the tool.
Serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
3.
Never leave the tool running unattended. Turn
the power off. Do not leave tool until it comes
to a complete stop.
4.
Do not operate saw without guards in place.
Check blade guard for proper closing before
each use. Do not operate saw if blade guard
does not move freely and close instantly.
Never clamp or tie the blade guard into the
open position.
5.
Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
6.
To reduce the risk of injury, return carriage
to the full rear position after each crosscut
operation.
7.
Always secure all moving portions before
carrying the tool.
8.
Stopper pin or stopper lever which locks
the saw head down is for carrying and stor-
age purposes only and not for any cutting
operations.
9.
Check the blade carefully for cracks or dam-
age before operation. Replace cracked or dam-
aged blade immediately. Gum and wood pitch
hardened on blades slows saw and increases
potential for kickback. Keep blade clean by
first removing it from tool, then cleaning it with
gum and pitch remover, hot water or kerosene.
Never use gasoline to clean blade.
10.
While making a slide cut, KICKBACK can
occur. KICKBACK occurs when the blade
binds in the workpiece during a cutting oper-
ation and the saw blade is driven rapidly
towards the operator. Loss of control and seri-
ous personal injury can result. If blade begins
to bind during a cutting operation, do not con-
tinue to cut and release switch immediately.
11.
Use only flanges specified for this tool.
12.
Be careful not to damage the arbor, flanges
(especially the installing surface) or bolt.
Damage to these parts could result in blade
breakage.
13.
Make sure that the turn base is properly
secured so it will not move during operation.
Use the holes in the base to fasten the saw to a
stable work platform or bench. NEVER use tool
where operator positioning would be awkward.
14.
Make sure the shaft lock is released before the
switch is turned on.
15.
Be sure that the blade does not contact the
turn base in the lowest position.
16.
Hold the handle firmly. Be aware that the saw
moves up or down slightly during start-up and
stopping.
17.
Make sure the blade is not contacting the
workpiece before the switch is turned on.
18.
Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced blade.
19.
Stop operation immediately if you notice any-
thing abnormal.
20.
Do not attempt to lock the trigger in the "ON"
position.
21.
Always use accessories recommended in this
manual. Use of improper accessories such as
abrasive wheels may cause an injury.
Содержание LS004GZ
Страница 43: ...43...