background image

19

ENGLISH

Tilting the circular saw blade to the 
right

1.

 

Rotate the knob on the slide pole 

counterclockwise.

2.

 

Hold the handle and tilt the carriage to the left 

slightly.

3.

 

Tilt the carriage to the right while pressing the 

releasing button for right side bevel angle.

4.

 

Align the pointer with your desired angle on the 

bevel angle scale.

5.

 

Tighten the knob clockwise to secure the carriage 

arm.

2

3

4

1

►    

1.

 Knob 

2.

 Handle 

3.

 Releasing button for right side 

bevel angle 

4.

 Bevel angle scale

Tilting the circular saw blade using 
positive stop function

This miter saw employs positive stop function. You can 
set 22.5° and 33.9° angle to both right and left quickly.

1.

 

Rotate the knob on the slide pole 

counterclockwise.

2.

 

Tilt the carriage close to your desired positive stop 

angle while raising the latch lever up.

3.

 

Set the latch lever in a horizontal position.

4.

 

Tilt the carriage at your desired positive stop angle 

until it is secured.

5.

 

To change the angle, pull the latch lever towards 

the front of the tool, and then re-tilt the carriage.

6.

 

Tighten the knob clockwise to secure the carriage 

arm.

1

2

►    

1.

 Knob 

2.

 Latch lever

Содержание LS004GZ













































Отзывы: