![background image](http://html2.mh-extra.com/html/makita/jv001gz/jv001gz_instruction-manual_4794554007.webp)
7 ENGLISH
NOTE:
The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE:
The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Declarations of Conformity
For European countries only
The Declarations of conformity are included in Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING
Read all safety warnings, instruc-
tions, illustrations and specifications provided with
this power tool.
Failure to follow all instructions listed
below may result in electric shock, fire and/or serious
injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Cordless jig saw safety warnings
1.
Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden wir-
ing.
Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
2.
Use clamps or another practical way to secure
and support the workpiece to a stable plat-
form.
Holding the workpiece by hand or against
your body leaves it unstable and may lead to loss
of control.
3.
Always use safety glasses or goggles.
Ordinary eye or sun glasses are NOT safety
glasses.
4.
Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
5.
Do not cut oversize workpiece.
6.
Check for the proper clearance around the
workpiece before cutting so that the jig saw
blade will not strike the floor, workbench, etc.
7.
Hold the tool firmly.
8.
Make sure the jig saw blade is not contacting
the workpiece before the switch is turned on.
9.
Keep hands away from moving parts.
10.
Do not leave the tool running. Operate the tool
only when hand-held.
11.
Always switch off and wait for the jig saw blade
to come to a complete stop before removing
the jig saw blade from the workpiece.
12.
Do not touch the jig saw blade or the work-
piece immediately after operation; they may be
extremely hot and could burn your skin.
13.
Do not operate the tool at no-load
unnecessarily.
14.
Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
15.
Always use the correct dust mask/respirator
for the material and application you are work-
ing with.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Important safety instructions for
battery cartridge
1.
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2.
Do not disassemble or tamper with the battery
cartridge.
It may result in a fire, excessive heat,
or explosion.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5.
Do not short the battery cartridge:
(1)
Do not touch the terminals with any con-
ductive material.
(2)
Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3)
Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6.
Do not store and use the tool and battery car-
tridge in locations where the temperature may
Содержание JV001GZ
