background image

C

ircuit  diagram

W

iring  diagram

P 2

2

/ 2

3

 

Red

White

Color index of lead wires' sheath

Black

Models HR4501C and HR4510C with Lock ON Switch

Power supply cord

Controller

Motor
 Housing

Controller is connected 
directly to Brush holder 
unit which is assembled
to Field.

Handle

Handle
Cover

Lead wire of  B  is 

brown

 for some countries

instead of black.

Lead wire of  A  is

blue 

for some countries

instead of white.

Lock ON Switch

Insulated 

Receptacle

A

B

Lead unit

Switch box

Switch box

Lead wire from 
Controller

from Lock ON Switch
in Switch box

Lead wires to
ON / OFF Switch

Do not to pinch the Lead 
wires at this position when
assembling Handle.

Viewed from Motor housing side

Motor Housing

Handle

Switch Box viewed from 

back side 

Fix the Lead wires 
of Lead unit (white)
and Switch lead
wire (red) with 
Lead wire holder.

Lead wire
holder

Lead wire
holder

Fix the Lead wires
with Lead wire holder
as illustrated left.

The Lead wires, fixed with Lead 
wire holder, are as follows.
 * Switch lead wire (red)
 * Lead wire (black) of Lead unit

Lock ON Switch

Viewed from Handle cover side

Fig. D-4

Fig. D-3

Opening for 
Guiding Lead wire 

Models HR4501C and HR4510C with Lock ON Switch

Main Switch

(ON / OFF Switch)

Main Switch

(ON / OFF Switch)

Содержание HR4501C
























Отзывы: