background image

12

ENGLISH

For depressed center wheel, flap disc, 

flex wheel, wire wheel brush / abrasive 

cut-off wheel, diamond wheel

1.

 

While pushing the lock lever, mount the wheel 

guard with the protrusions on the wheel guard aligned 
with the notches on the bearing box.

1

2

3

Fig.6

►    

1.

 Lock lever 

2.

 Notch 

3.

 Protrusion

2.

 

While pushing the lock lever toward A, hold down 

the portions B of the wheel guard as shown in the figure.

2

B

1

A

B

Fig.7

►    

1.

 Wheel guard 

2.

 Hole

NOTE:

 Push down the wheel guard straight. 

Otherwise, you cannot secure the wheel guard.

3.

 

While pushing the lock lever toward A, rotate the 

wheel guard toward C, and then, change the angle of 
the wheel guard according to the work so that the oper-
ator can be protected. Align the lock lever with one of 
the holes in the wheel guard, and then release the lock 
lever to lock the wheel guard.

2

1

A

C

C

Fig.8

►    

1.

 Wheel guard 

2.

 Hole

To remove wheel guard, follow the installation proce-
dure in reverse.

Clip-on cutting wheel guard 
attachment

Optional accessory

NOTE:

 For cutting-off operations, a clip-on cutting 

wheel guard attachment can be used with the wheel 

guard (for grinding wheel).

Not available in some countries.

Fig.9

Содержание GA049G

























Отзывы: