Makita G7300R Скачать руководство пользователя | Manualshive

Страница: 31 / 42

background image

8. MAINTENANCE SCHEDULE

−

25

−

ENGLISH

DAILY INSPECTION

Before running the generator, check the following service items:

Excessive vibration,noise

Clean air cleaner element

Safe surroundings

Enough clean engine oil

Leakage of gasoline and engine oil

Loose or broken bolts and nuts

Enough gasoline

PERIODIC MAINTENANCE

Periodic maintenance is vital to safe and efficient operation of your generator.
Check the table below for periodic maintenance intervals.

IT IS ALSO NECESSARY FOR THE USER OF THIS GENERATOR TO
CONDUCT THE MAINTENANCE AND ADJUSTMENTS ON THE EMISSION-
RELATED PARTS LISTED BELOW TO KEEP THE EMISSION CONTROL
SYSTEM EFFECTIVE.

The emission control system consists of the following parts :

The maintenance schedule indicated in the table is based on the normal generator
operation. Should the generator be operated in extremely dusty condition or in
heavier loading condition, the maintenance intervals must be shortened depending
on the contamination of oil, clogging of filter elements, wear of parts, and so on.

(1) Carburetor and internal

parts

(2) Cold start enrichment

system, if applicable

(3) Intake manifold, if

applicable

(4) Air cleaner elements

(5) Spark plug

(6) Magneto or electronic

ignition system

(7) Spark advance/retard

system, if applicable

(8) Exhaust manifold, if

applicable

(9) Hoses, belts,

connectors, and
assemblies

MAINTENANCE, REPLACEMENT OR REPAIR OF THE EMISSION CONTROL DEVICES
AND SYSTEMS MAY BE PERFORMED BY ANY NONROAD ENGINE REPAIR
ESTABLISHMENT OR INDIVIDUAL.

G7300取説̲GU2043 05.1.26 11:27 AM ページ25

«
...
29
30
31
32
33
...
»

Содержание G7300R











































Отзывы:

Нет отзывов

Похожие инструкции для G7300R

Бренд: Sangean Страницы: 15

Бренд: Sangean Страницы: 10

Бренд: TR Страницы: 16

Бренд: Mase Generators Страницы: 92

Бренд: Briggs & Stratton Страницы: 7

Бренд: Predator Страницы: 24

Бренд: Vertex Standard Страницы: 34

Бренд: Reflexion Страницы: 49

Бренд: Tektronix Страницы: 12

Бренд: Wacker Neuson Страницы: 200

Modular Power Series

Бренд: ICT Страницы: 91

Бренд: Coleman Страницы: 8

Powermate PM0463300.01

Бренд: Coleman Страницы: 12

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

COLOR TV 5 INCH RD0525C

Бренд: Philips Страницы: 2

COLOR TV 5 INCH RD0525C

Бренд: Philips Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды