Makita G7300R Скачать руководство пользователя | Manualshive

Страница: 27 / 42

background image

(1) HOW TO USE IDLE CONTROL

■

Start the engine with IDLE CONTROL
SWITCH off.

NOTE :

Warm up the engine without a load for a
few minutes.

■

Turn IDLE CONTROL SWITCH on.

(2) CHECKING THE OPERATION

When IDLE CONTROL does not operate normally, please check following :

■

Overloaded ?
Please make it sure that the generator is not overload.

NOTE :

Most induction loads such as electric motors require three to five times more
wattage than their ratings during starting.
This starting wattage should not exceed the rated output of the generator for proper
operation of IDLE CONTROL.

■

Turn IDLE CONTROL SWITCH off when the IDLE CONTROL does not work
normally under the rated output.

NOTE :

The IDLE CONTROL may not operate when the applied load is under 40W. In such
cases turn the IDLE CONTROL SWITCH off.

(3) STOPPING THE ENGINE

■

Turn off the switch of load.

■

Switch off generator's AC breaker.

■

Disconnect tool or appliance.

■

Turn the IDLE CONTROL SWITCH off.

■

Turn the STOP SWITCH to the position "O" (OFF).

NOTE :

Allow the engine about 3 minutes to cool down at no-load before stopping.

IDLE CONTROL

IDLE CONTROL automatically reduces engine speed when load is OFF, and
automatically increases engine speed to rated r.p.m. when load is ON.
IDLE CONTROL provides fuel economy and low noise operation at no-load
running.

−

21

−

ENGLISH

ON

OFF

G7300取説̲GU2043 05.1.26 11:27 AM ページ21

«
...
25
26
27
28
29
...
»

Содержание G7300R











































Отзывы:

Нет отзывов

Похожие инструкции для G7300R

Бренд: Feider Machines Страницы: 36

Бренд: Garland Страницы: 120

Бренд: Southwest Windpower Страницы: 42

Бренд: All-Power Страницы: 14

Бренд: auna Страницы: 18

Бренд: Sytech Страницы: 4

Бренд: U.S. Products Страницы: 8

Бренд: Powermate Страницы: 12

Бренд: Jung Страницы: 10

Бренд: Curtis Страницы: 8

Бренд: Curtis Страницы: 18

Бренд: Majestic Страницы: 41

Бренд: PROTRON Страницы: 44

Бренд: Pulsar Страницы: 26

Бренд: Pulsar Страницы: 26

Бренд: Yamato Страницы: 36

Бренд: Chicago Electric Страницы: 13

Powermate PM0545007 Insert

Бренд: Coleman Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды