background image

14

REFUELING

Handling of fuel

It is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be performed in a sufficiently 

ventilated room or in the open air. Never inhale fuel vapor, and keep fuel away from you. If you touch fuel repeatedly or for a long time, the 

skin becomes dry, which may cause skin disease or allergy. If fuel enters into the eye, clean the eye with fresh water. If your eye remains still 

irritated, consult your doctor.

Storage period of fuel

Fuel should be used up within a period of 4 weeks, even if it is kept in a special container in a well-ventilated shade.  

If a special container is not used or if the container is not covered, fuel may deteriorate in one day.

Refueling
WARNING: INFLAMMABLES STRICTLY PROHIBITED

Gasoline used: 

Automobile gasoline (unleaded gasoline)

–   Loosen the tank cap a little so that there will be no difference in atmospheric 

pressure. 

–   Detach the tank cap, and refuel, discharging air by tilting the fuel tank so 

that the refuel port will be oriented upward. (Never refill fuel full to the oil refill 

port.) 

–   Wipe well the periphery of the tank cap to prevent foreign matter from 

entering into the fuel tank. 

–   After refueling, securely tighten the tank cap. 

●  If there is any flaw or damage on the tank cap, replace it.
●  The tank cap is consumable, and therefore should be renewed every two to 

three years.

Fuel tank cap

Fuel upper limit

Fuel tank

Fuel

The engine is a four-stroke engine. Be sure to use an automobile gasoline (regular gasoline or premium gasoline). 

Point 2 in Replacement of oil: “If oil spills out”

–   If oil spills out between the fuel tank and engine main unit, the oil is sucked into through the cooling air intake port, which will 

contaminate the engine. Be sure to wipe out spilt oil before start of operation. 

STORAGE OF MACHINE AND REFILL TANK

–   Keep the machine and tank at a cool place free from direct sunshine.
–   Never keep the fuel in the cabin or trunk.

Points for fuel

–   Never use a gasoline mixture which contains engine oil. Otherwise, it will cause excessive carbon accumulation or mechanical troubles. 
–   Use of deteriorated oil will cause irregular startup. 

Содержание EBH252U

















































































Отзывы: