![background image](http://html.mh-extra.com/html/makita/dwr180/dwr180_instruction-manual_230552007.webp)
7 ENGLISH
Switch action
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch lever actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch lever. Tool speed
is increased by increasing pressure on the switch lever.
Release the switch lever to stop.
►
Fig.3:
1.
Switch lever
NOTE:
The tool automatically stops when you keep
pulling the switch trigger for about 1 minute.
To prevent the switch lever from accidentally pulled, the
lock lever is provided.
When the lock lever is in the lock position , the switch
lever cannot be actuated.
When the lock lever is in the unlock position , the
switch lever can be actuated.
►
Fig.4:
1.
Lock lever
2.
Lock
3.
Unlock
CAUTION:
When not operating the tool,
always slide the lock lever to the lock position .
Lighting up the front lamp
CAUTION:
Do not look in the light or see the
source of light directly.
Pull the switch lever to light up the lamp. The lamp
keeps on lighting while the switch lever is being pulled.
The light automatically goes out approximately 10 sec
-
onds after the switch lever is released.
►
Fig.5:
1.
Switch lever
2.
Lamp
NOTICE:
When the tool is overheated, the lamp
blinks. Cool down the tool fully before operating the
tool again.
NOTICE:
Use a dry cloth to wipe the dirt off the lens
of the lamp. Be careful not to scratch the lens of lamp,
or it may lower the illumination.
Reversing lever action
CAUTION:
Always check the direction of
rotation before operation.
CAUTION:
Use the reversing lever only after
the tool comes to a complete stop.
Changing the
direction of rotation before the tool stops may dam
-
age the tool.
This tool has a reversing lever to change the direction
of rotation. Turn the reversing lever to the A side for
clockwise rotation or to the B side for counterclockwise
rotation.
Make sure that the reversing lever is fully turned with
a click.
►
Fig.6:
1.
Reversing lever
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing socket
adaptor
To install the socket adaptor, push it into the adaptor
hole until it locks into place.
►
Fig.7:
1.
Socket adaptor
2.
Adaptor hole
To remove the socket adaptor, insert a stick like a
screwdriver into the backside of the socket adaptor, and
then tap it gently.
►
Fig.8:
1.
Socket adaptor
2.
Screwdriver
NOTICE:
During removal procedure, keep holding
the socket adaptor to prevent it from falling off from
the tool.
Installing or removing socket
CAUTION:
Before operation, make sure that
the socket is properly locked onto the socket
adaptor.
Incomplete attachment of the socket may
cause injury.
NOTICE:
Always use the correct size socket for bolt/
nut. An incorrect size socket will result in inconsistent
fastening torque and/or damage to the bolt/nut.
To install the socket, push it onto the socket adaptor
until it locks into place. To remove the socket, simply
pull it off.
►
Fig.9:
1.
Socket
2.
Socket adaptor
OPERATION
CAUTION:
Hold the tool firmly especially
when the bolt/nut reaches the seating position.
The socket stops rotating and the motor reaction
generate instant backlash to rotate the tool.
NOTICE:
Hold the tool pointed straight at the
bolt/nut.
Hold the tool firmly and place the socket over the
bolt/nut. Turn the tool on and fasten. When the bolt/
nut reaches the seating position, the tool stops
automatically.
►
Fig.10
The tool also works without socket. The adaptor hole
can fasten M8 (5/16") bolt/nut. (works as 13mm socket)
►
Fig.11
Содержание DWR180
Страница 2: ...1 2 3 Fig 1 1 2 Fig 2 1 Fig 3 1 2 3 Fig 4 2 1 Fig 5 A B 1 Fig 6 1 2 Fig 7 1 2 Fig 8 2 ...
Страница 3: ...1 2 Fig 9 Fig 10 Fig 11 Fig 12 3 ...
Страница 55: ...55 ...