![background image](http://html.mh-extra.com/html/makita/dwr180/dwr180_instruction-manual_230552004.webp)
4 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
DWR180
Fastening capacities
(with manual retightening)
Standard bolt
M5 - M12
High tensile bolt
M5 - M10
Square drive
6.35 mm, 9.5 mm
No load speed
0 - 800 min
-1
Maximum fastening torque
47.5 N•m
Overall length
369 mm
Rated voltage
D.C. 18 V
Net weight
1.2 - 1.6 kg
•
Due to our continuing program of research and development, the specifications herein are subject to change without notice.
•
Specifications and battery cartridge may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi
-
est combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
Charger
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
DC18SH
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above.
Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for fastening bolts and nuts.
Noise
The typical A-weighted noise level determined accord
-
ing to EN62841-2-2:
Sound pressure level (L
pA
) : 74 dB(A)
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
NOTE:
The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE:
The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-2:
Work mode: fastening
Vibration emission (a
h
) : 2.5 m/s
2
Uncertainty (K) : 1.5 m/s
2
NOTE:
The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE:
The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared val
-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
Содержание DWR180
Страница 2: ...1 2 3 Fig 1 1 2 Fig 2 1 Fig 3 1 2 3 Fig 4 2 1 Fig 5 A B 1 Fig 6 1 2 Fig 7 1 2 Fig 8 2 ...
Страница 3: ...1 2 Fig 9 Fig 10 Fig 11 Fig 12 3 ...
Страница 55: ...55 ...