18 ENGLISH
connection cord
for
loose
connection with
the
switch
box
and
the
shears.
If
the
lamps
still
blink
alternately, stop
using
the
tool
immediately,
disconnect the
connection cord,
remove
the
battery,
and ask
your local authorized service center for repair.
Lamps
blink
alternately
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing the battery holder into the
backpack
►
Fig.9:
1.
Clamp
2.
Battery holder
3.
Strap
1.
Pass
the
switch
box
through
the
opening
(either
right
or
left)
of
the
back
pack.
2.
Pass
the
clamp
through
the
square
hole
of
the
battery
holder,
and
secure
the
battery
holder
with
the
strap.
Make
sure
that
the
battery
holder
sits
in
the
backpack firmly.
Installing the holster
►
Fig.10:
1.
Holster
2.
Strap
Pass
the
belt
of
the
lower
buckle
through
the
opening
of
the
holster.
Adjusting the harness
Adjust
the
harness
as
follows:
1.
Close
and
lock
the
lower
buckle,
and
adjust
its
belt
length. ►
Fig.11:
1.
Lower
buckle
2.
Adjust
the
shoulder
strap
length. ►
Fig.12
3.
Adjust
the
position
of
the
upper
buckle.
Close
and
lock
the
upper
buckle
and
adjust
its
belt
length. ►
Fig.13:
1.
Upper
buckle
CAUTION:
In case of emergency, quickly
open the lower buckle and upper buckle, loosen
shoulder straps, and set down the backpack.
Installing the connection cord
CAUTION:
Always make sure that the switch
box's I/O switch is on the "O" side before
attaching the connection cord.
CAUTION:
Do not operate the tool if the
connection cord is damaged.
NOTICE:
Do
not
abuse
the
connection cord.
Do
not
carry
the
tool
by
pulling
the
connection cord.
Keep
the
connection cord
away from heat, oil, or sharp edges. Otherwise
the
connection cord
may
be
damaged.
Attach
the
connection cord
with
the
switch
box
and
the
shears as follows:
1.
First, align the triangular marks of the male
plug of the connection cord with the triangular mark of
the female connector of
the
switch
box.
Push
in
the
plug
of
the
connection cord
to
the
connector of
the
switch
box.
Then, align the marking on the
coupling with the trianglar marks, and push in and turn
the coupling to tighten.
►
Fig.14:
1.
Triangular mark
2.
Connection
cord
3.
Switch box
4.
Marking on
coupling
5.
Coupling
NOTICE:
Turn the coupling and align the marking on
the
coupling
with
the
triangular marks
first
when
disconnecting
the
connection cable.
2.
Hang
the
switch
box
on
the
waist
belt
or
upper
belt. ►
Fig.15
3.
Push the connection cord into the loop of
the cord holder.
►
Fig.16
Hang
the
cord
holder
on
either
the
upper
belt
or
the
waist
belt
on
which
the
switch
box
is
not
hung.
Содержание DUP361
