![background image](http://html1.mh-extra.com/html/makita/dtr181zj/dtr181zj_instruction-manual_4144254017.webp)
17 ENGLISH
Main power switch
CAUTION:
When you turn the power on, never
bring your limbs or face close to the binding or rotat
-
ing parts of the tool tip.
Otherwise, you may be injured.
CAUTION:
When the power is turned on,
never touch the binding or rotating parts of the
tool tip.
Otherwise, you may be injured.
CAUTION:
Before inserting the battery cartridge,
be sure to release your fingers from the switch trigger
and lock the trigger.
If you insert the battery cartridge
while the switch trigger is being pulled, it may cause an
accident if the wire tying process is accidentally carried out.
►
Fig.3
When you press the power button, the power turns
on and the tying mode lamp lights up. In order for the
tool to adjust its initial position, it operates temporarily.
When adjustment has completed, the tool stops auto
-
matically. When you press the power button again, the
power turns off and the tying mode lamp goes out.
►
Fig.4:
1.
Tying mode lamp
2.
Power button
NOTE:
The tool has an auto power-off function. If the
switch trigger is not pulled for 10 minutes, the tool is auto-
matically turned off to reduce battery power consumption.
NOTE:
To restart the tool, turn the power on again.
Mode switching button
When the power is turned on and the tying mode lamp
is lit, you can select the single actuation mode or the
continuous actuation mode via the mode switching but-
ton. When you turn the power on again, the tool starts in
the mode that was most recently selected.
►
Fig.5:
1.
Mode switching button
2.
Single actuation
mode
3.
Continuous actuation mode
Switch action
WARNING:
Before installing the battery car
-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
CAUTION:
When not operating the tool,
depress the trigger-lock button from
side to
lock the switch trigger in the OFF position.
►
Fig.6:
1.
Switch trigger
2.
Trigger-lock button
To prevent the switch trigger from accidentally pulled,
the trigger-lock button is provided. To start the tool,
depress the trigger-lock button from A side and pull the
switch trigger. Release the switch trigger to stop. After
use, press in the trigger-lock button from B side.
When you pull the switch trigger, the tool performs the
next sequential operations as follows, and the tool stops
automatically.
1. Feed the wire.
2. Cut the wire.
3. The hook holds and twists the wire.
4. The hook returns to the original position.
Tying strength setting
CAUTION:
Be sure to lock the trigger before
starting the adjustment. When you turn the power
on, never bring your limbs or face close to the
binding or rotating parts of the tool tip.
Otherwise,
you may be injured.
►
Fig.7
You can set the tying strength by adjusting the tying
strength adjusting button. Tying strength is shown on
the display panel.
►
Fig.8:
1.
Tying strength adjusting button
2.
Display
panel
If the wire is broken off, tying strength will be lost. After
tying, check the twisted portion for breakage.
If the wire is broken off, adjust the tying strength using
the tying strength adjusting button, and tie the rebars
again.
Remaining battery notification
When the battery voltage drops below the required
level, the tool will stop operating, an error tone will
sound, and the number "4" will appear on the display
panel. The error tone will continue to sound until the
power is turned off.
NOTE:
If the ambient temperature is extremely low,
the error tone may sound even when the battery
contains sufficient power.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Loading the tie wire (wire reel)
CAUTION:
Before mounting or dismounting
tie wires and accessories, be sure to turn the
power off, lock the trigger, and remove the battery
cartridge.
Failure to do so may cause an accident.
NOTICE:
Using wires other than Makita's genu
-
ine tie wires may cause the tool to malfunction.
1.
Push the release lever, and lock it with the lock
lever.
►
Fig.9:
1.
Release lever
2.
Lock lever
When you push the release lever, a gap is created
between the left and right feed gears.
►
Fig.10:
1.
Release lever
2.
Lock lever
3.
Feed gears
2.
Open the reel cover.
►
Fig.11:
1.
Reel cover
3.
Mount the wire reel on the tool in the orientation
shown in the figure.
►
Fig.12:
1.
Wire reel
Содержание DTR181ZJ
