background image

16 ENGLISH

Switch action

WARNING:

 

Before installing the batteries 

into the tool, always check to see that the switch 

trigger actuates properly and returns to the "OFF" 

position when released. Do not pull the switch 

trigger hard without pressing in the lock-off but-

ton. This can cause switch breakage.

 Operating a 

tool with a switch that does not actuate properly can 

lead to loss of control and serious personal injury.

WARNING:

 

NEVER use tool without a fully 

operative switch trigger.

 Any tool with an inoper

-

ative switch is HIGHLY DANGEROUS and must be 

repaired before further usage or serious personal 

injury may occur.

WARNING:

 

NEVER defeat the lock-off button 

by taping down or some other means.

 A switch with 

a negated lock-off button may result in unintentional 

operation and serious personal injury.

WARNING:

 

NEVER use the tool if it runs when 

you simply pull the switch trigger without press-

ing the lock-off button.

 A switch in need of repair 

may result in unintentional operation and serious 

personal injury. Return tool to a Makita service center 

for proper repairs BEFORE further usage.

1

2

3

►    

1.

 Switch trigger 

2.

 Lock-off button 

3.

 Hole for 

padlock

To prevent the switch trigger from being accidentally 

pulled, a lock-off button is provided. To start the tool, 

press in the lock-off button and pull the switch trigger. 

Release the switch trigger to stop.

A hole is provided in the switch trigger for insertion of a 

padlock to lock the tool off.

WARNING:

 

Do not use a lock with a shank or 

cable any smaller than 6.35 mm (1/4") in diameter.

 

A smaller shank or cable may not properly lock the 

tool in the off position and unintentional operation 

may occur resulting in serious personal injury.

Electronic function

Constant speed control

The tool is provided with an electronic speed control 

which helps maintain a constant blade rotation speed 

even under load. A constant blade rotation speed will 

result in a very smooth cut.

Soft start feature

This function allows the smooth start-up of the tool by 

limiting the start-up torque.

Laser beam action

For DLS112 only

CAUTION:

 

Never look into the laser beam.

 

Direct laser beam may injure your eyes.

To turn on the laser beam, press the upper position (I) 

of the switch. To turn off the laser beam, press the lower 

position (0) of the switch.

1

►    

1.

 Switch for laser

Laser line can be shifted to either the left or right side of 

the saw blade by turning the adjusting screw as follows.

1

►    

1.

 Adjusting screw

1.

  Loosen the adjusting screw by turning it 

counterclockwise.

2.

  With the adjusting screw loosened, slide the 

adjusting screw to the right or left as far as it goes.

3.

  Tighten the adjusting screw firmly at the position 

where it stops sliding.

NOTE:

 Laser line is factory adjusted so that it is posi

-

tioned within 1 mm from the side surface of the blade 

(cutting position).

NOTE:

 When laser line appears dim and hard to see 

because of direct sunlight, relocate the work area to a 

place where there is less direct sunlight.

Aligning the laser line

Align the cutting line on your workpiece with the laser 

line.

Содержание DLS112

































Отзывы: