![background image](http://html.mh-extra.com/html/makita/df012d/df012d_instruction-manual_1722688007.webp)
7 ENGLISH
Switch action
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch actuates properly and returns to the "OFF"
position when released.
CAUTION:
Always check the direction of
rotation before operation.
►
Fig.3:
1.
Lock lever
2.
Switch
To start the tool, first move the lock lever to the
unlocked position A to release the switch. And then sim
-
ply push the switch on the
C side for the clockwise
rotation and the
D side for the counterclockwise
rotation. Release the switch to stop.
NOTICE:
Change the direction only after the tool
comes to a complete stop.
Changing the direction
of rotation before the tool stops may damage the tool.
Speed change
►
Fig.4:
1.
Speed change lever
CAUTION:
Always set the speed change lever
fully to the correct position.
If you operate the tool with
the speed change lever positioned halfway between the
"1" side and "2" side, the tool may be damaged.
CAUTION:
Do not use the speed change lever
while the tool is running.
The tool may be damaged.
Position of
speed
change lever
Speed
Torque
Applicable
operation
1
Low
High
Heavy load
-
ing operation
2
High
Low
Light loading
operation
To change the speed, switch off the tool first. Select the "2" side for
high speed or "1" for low speed but high torque. Be sure that the
speed change lever is set to the correct position before operation.
If the tool speed is coming down extremely during the opera
-
tion with "2", slide the lever to the "1" and restart the operation.
Adjusting the fastening torque
►
Fig.5:
1.
Adjusting ring
2.
Graduation
3.
Arrow
The fastening torque can be adjusted in 22 levels by turning the adjusting ring. Align the graduations with the arrow
on the tool body. You can get the minimum fastening torque at 1 and maximum torque at
marking.
The clutch will slip at various torque levels when set at the number 1 to 21. The clutch does not work at the
marking.
Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which
torque level is required for a particular application.
NOTE:
See the following chart for the relation between the number of torque setting and fastening torque rate.
The fastening torque rate will be different depends on materials. Make a test fastening to get the desired torque before operation.
Guideline for clutch auto stop
Work range of clutch auto-stop
Increments on adjusting ring
for fastening torque
Fastening torque
High
Low
1
Approx. 0.3 N•m
(Approx. 3 Kgf•cm)
5
Approx. 0.82 N•m
(Approx. 8.4 Kgf•cm)
9
Approx. 1.35 N•m
(Approx. 13.8 Kgf•cm)
-
13
Approx. 1.88 N•m
(Approx. 19.2 Kgf•cm)
-
17
Approx. 2.41N•m
(Approx. 24.6 Kgf•cm)
-
21
Approx. 2.9 N•m
(Approx. 30 Kgf•cm)
-
-
At low speed, approx. 8 N•m
(Approx. 81.6 Kgf•cm)
-
-
At high speed, approx. 1.5 N•m
(Approx. 14.7 Kgf•cm)
When driving machine screws
Increments
Guideline for machine screw diameter
1 - 3
2.5 mm
4 - 8
3 mm
9 - 18
4 mm
19 - 21
5 mm
Содержание DF012D
Страница 3: ...1 3 2 Fig 9 1 2 Fig 10 Fig 11 Fig 12 3 ...