4
ENGLISH
Explanation of general view
1
Clamper
2
Conventional type of abrasive
paper with pre-punched holes
3
Pad for conventional type of
abrasive paper
4
Punch plate
5
Conventional type of abrasive
paper without pre-punched
holes
6
Screws
7
Screwdriver
8
Hook-and-loop type of
abrasive paper with
pre-punched holes
9
Pad for hook-and-loop type of
abrasive paper
10
Dust bag
11
Dust spout
12
Switch trigger
13
Lock button
SPECIFICATIONS
Model
BO3700
Pad size ................................................. 93 mm x 185 mm
Abrasive paper size ............................... 93 mm x 228 mm
Orbits per minute .................................................. 10,000
Overall length ......................................................254 mm
Net weight ..............................................................1.4 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for the sanding of large surface of
wood, plastics and metal materials as well as painted
surfaces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1.
Hold the tool firmly.
2.
Do not leave the tool running. Operate the tool
only when hand-held.
3.
This tool has not been waterproofed, so do not
use water on the workpiece surface.
4.
Ventilate your work area adequately when you
perform sanding operations.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing abrasive paper
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the abrasive
paper.
For conventional type of abrasive paper with pre-
punched holes (standard equipment):
Press the clamper. Insert the paper end into the clamper,
aligning the holes in the paper with those in the pad.
Then release the clamper to secure the paper. Repeat
the same process for the other end of the base, maintain-
ing the proper paper tension.
(Fig. 1)
For conventional type of abrasive paper without pre-
punched holes (available on the market):
Press the clamper. Insert the paper end into the clamper,
aligning the paper edges even and parallel with the sides
of the base. Then release the clamper to secure the
paper. Repeat the same process for the other end of the
base, maintaining the proper paper tension. Place the
punch plate (optional accessory) over the paper so that
the guide of the punch plate is flush with the sides of the
base. Then press the punch plate to make holes in the
paper.
(Fig. 2)
For hook-and-loop type of abrasive paper with pre-
punched holes (optional accessory):
Remove the pad for the conventional type of abrasive
paper from the tool with a screwdriver.
(Fig. 3)
Install the pad for the hook-and-loop type of abrasive
paper (optional accessory) on the tool. Tighten the
screws firmly to secure the pad. Remove all dirt or for-
eign matter from the pad. Attach the paper to the pad,
aligning the holes in the paper with those in the pad.
(Fig. 4)
CAUTION:
Always use hook-and-loop type of abrasive papers.
Never use pressure-sensitive abrasive paper.
Installing dust bag (Fig. 5)
Attach the dust bag onto the dust spout. The dust spout
is tapered. When attaching the dust bag, push it onto the
dust spout firmly as far as it will go to prevent it from com-
ing off during operation. For the best results, empty the
dust bag when it becomes about half full, tapping it lightly
to remove as much dust as possible.
