Makita BMR100 Скачать руководство пользователя страница 8

Страница: 8 / 72

Slide Battery:

9.6V: BH9033 | BH9033A | BH9020 | BH9020A
12V: BH1233 | BH1233C | BH1220C
14.4V: BH1433 | BH1420 | BL1430
18V: BL1830
24V: BH2433

BH2420

The following tables indicate the operating time on a
single charge.

* Operating time may differ by the type of battery, charging or

operating conditions.

3-1. Installing or removing Slide

battery cartridge (Fig. 3)

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being
inserted correctly.

• To remove the battery cartridge, withdraw it from the

tool while sliding the button on the front of the cartridge
or pressing the buttons on both sides of the cartridge.

3-2. Installing or removing Cluster

battery cartridge (Fig. 4)

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip
it into place.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being
inserted correctly.

• To remove the battery cartridge, withdraw it from the

Job site radio.

Replace battery compartment locker.

Reduced power, distortion and a “stuttering sound” or
low battery sign

that appears on the display are

all the signs that the main battery pack needs to
replace.

Note:

The battery pack can’t be charged via the supplied AC
power adaptor.

When low battery sign

appears and an “E” keeps

on flashing is the time to replace the back up batteries.

Installing the Soft bended rod

antenna (Fig. 5)

Install the Soft bended rod antenna as show in the figure.

Using Supplied AC power adaptor

(Fig. 6)

Remove the rubber protector and insert the adaptor plug
into the DC socket on the front side of the radio. Plug the
adaptor into a standard mains socket outlet. Whenever
the adaptor is used, the battery pack are automatically
disconnected. The AC adaptor should be disconnected
from the main supply when not in use.

Note:

When your radio has any interference in AM band by its
adaptor, please move your radio away from its AC
adaptor over 30 cm.

Setting the clock

Clock can be set either when the radio is power on or
off.

Display will show “-: - -” when the back up batteries
are installed.

Long press the time set button

for more than

2 seconds, display will flash time set symbol

and

also the hour digit, followed by a beep.

Rotate Tuning control to set the required hour.

Press

button to confirm hour setting, the minute

digit will flash.

Rotate Tuning control to set the required minute.

Press the

button again to complete clock setting.

Operating the radio

This radio equips with three tuning methods – Scan
tuning, Manual tuning and Memory presets recall.

Scan Tuning

Press the Power button to turn on the radio.

Select the required waveband by pressing the Band
button. Make sure the rubber bended rod antenna has
been well placed for best FM reception. For AM (MW)
band, rotate the radio to get best signal. Try to avoid to
operate the radio next to computer screen and other
equipment which will cause interference to the radio.

Press and release Scan button (long press Scan
button more than 2 seconds will activate time setting),
LCD display will flash Scan symbol and the radio will
up search and stop automatically when it finds a radio
station,. Press the Scan button again to pick up the
found station.

Note:

A stereo symbol will appear on the display, if the
station found is a stereo station.

Battery

Capacity

Battery Cartridge•Voltage

Operating time*

(At Max. Volume)

9.6V

12V

14.4V

18V

24V