14 ENGLISH
Super flange
Optional accessory
Super flange is a special accessory for model which is
NOT equipped with a brake function.
Models with the letter F are standard-equipped with
Super flange. Only 1/3 of efforts needed to undo lock
nut, compared with conventional type.
Installing or removing Ezynut
Optional accessory
Only for tools with M14 spindle thread.
CAUTION:
Do not use Ezynut with Super
Flange. Those flanges are so thick that the entire
thread cannot be retained by the spindle.
Mount inner flange, abrasive wheel and Ezynut onto the
spindle so that Makita Logo on Ezynut faces outside.
►
Fig.16:
1.
Ezynut
2.
Abrasive wheel
3.
Inner flange
4.
Spindle
Press shaft lock firmly and tighten Ezynut by turning the
abrasive wheel clockwise as far as it turns.
►
Fig.17:
1.
Shaft lock
To loosen the Ezynut, turn the outside ring of Ezynut
counterclockwise.
NOTE:
Ezynut can be loosened by hand as long
as the arrow points the notch. Otherwise a lock nut
wrench is required to loosen it. Insert one pin of the
wrench into a hole and turn Ezynut counterclockwise.
►
Fig.18:
1.
Arrow
2.
Notch
►
Fig.19
Installing abrasive cut-off / diamond
wheel
Optional accessory
WARNING:
When using an abrasive cut-off
/ diamond wheel, be sure to use only the special
wheel guard designed for use with cut-off wheels.
WARNING:
NEVER use cut-off wheel for side
grinding.
►
Fig.20:
1.
Lock nut
2.
Abrasive cut-off wheel / dia
-
mond wheel
3.
Inner flange
4.
Wheel guard
for abrasive cut-off wheel / diamond wheel
As for the installation, follow the instructions for
depressed center wheel.
The direction for mounting the lock nut and the inner
flange varies by wheel type and thickness.
Refer to the following figures.
When installing the abrasive cut-off wheel:
►
Fig.21:
1.
Lock nut
2.
Abrasive cut-off wheel
(Thinner than 4 mm (5/32"))
3.
Abrasive cut-
off wheel (4 mm (5/32") or thicker)
4.
Inner
flange
When installing the diamond wheel:
►
Fig.22:
1.
Lock nut
2.
Diamond wheel (Thinner than
4 mm (5/32″))
3.
Diamond wheel (4 mm
(5/32″) or thicker)
4.
Inner flange
Installing wire cup brush
Optional accessory
CAUTION:
Do not use brush that is damaged, or
which is out of balance.
Use of damaged brush could increase
potential for injury from contact with broken brush wires.
Place the tool upside down to allow easy access to the spindle.
Remove any accessories on spindle. Thread wire cup
brush onto spindle and tighten with supplied wrench.
►
Fig.23:
1.
Wire cup brush
Installing wire wheel brush
Optional accessory
CAUTION:
Do not use wire wheel brush that
is damaged, or which is out of balance.
Use of
damaged wire wheel brush could increase potential
for injury from contact with broken wires.
CAUTION:
ALWAYS use guard with wire
wheel brushes, assuring diameter of wheel fits
inside guard.
Wheel can shatter during use and
guard helps to reduce chances of personal injury.
Place the tool upside down to allow easy access to the spindle.
Remove any accessories on spindle. Thread wire wheel
brush onto spindle and tighten with the wrenches.
►
Fig.24:
1.
Wire wheel brush
Installing hole cutter
Optional accessory
Place the tool upside down to allow easy access to the spindle.
Remove any accessories on the spindle. Thread the hole cut
-
ter onto the spindle, and tighten it with the supplied wrench.
►
Fig.25:
1.
Hole cutter
Installing dust collecting wheel
guard for grinding
Optional accessory
With optional accessories, you can use this tool for
planing concrete surface.
CAUTION:
Dust collecting wheel guard for grind-
ing is only for use in planing concrete surface with a
cup-type diamond wheel. Do not use this guard with
any other cutting accessory or for any other purpose.
CAUTION:
Before operation, make sure that a
vacuum cleaner is connected to the tool and turned on.
Place the tool upside down and install the dust collecting wheel guard.
Mount the inner flange onto the spindle.
Fit the cup-type diamond wheel on the inner flange and
tighten the lock nut onto the spindle.
►
Fig.26:
1.
Lock nut
2.
Cup-type diamond wheel
3.
Hubbed cup-type diamond wheel
4.
Inner
flange
5.
Dust collecting wheel guard
6.
Bearing box
NOTE:
For information how to install the dust col-
lecting wheel guard, refer to the manual of the dust
collecting wheel guard.
Содержание 9565CVRKD
