background image

7

15. When operating the saw, keep the cord

away from the cutting area and position it
so that it will not be caught on the work-
piece during the cutting operation. The
tool is provided with a front grip and rear
handle for two hand operation. Operate
with proper hand support, proper work-
piece support, and supply cord routing
away from the work area.
WARNING: It is important to support the
workpiece properly and to hold the saw
firmly to prevent loss of control which
could cause personal injury. Fig. 4 illus-
trates typical hand support of the saw.

16. Place the wider portion of the saw base on

that part of the workpiece which is solidly
supported, not on the section that will fall
off when the cut is made. As examples,
Fig. 5 illustrates the RIGHT way to cut off
the end of a board, and Fig. 6 the WRONG
way. If the workpiece is short or small,
clamp it down. DO NOT TRY TO HOLD
SHORT PIECES BY HAND!

17. Never attempt to saw with the circular saw

held upside down in a vise. This is
extremely dangerous and can lead to seri-
ous accidents.

18. WARNING: Blade coasts to stop after

switch is released. Contact with coasting
blade can cause serious injury. Before
setting the tool down after completing a
cut, be sure that the lower (telescoping)
guard has closed and the blade has come
to a complete stop.

19. Some material contains chemicals which

may be toxic. Take caution to prevent dust
inhalation and skin contact. Follow mate-
rial supplier safety data.

Fig. 4

A typical illustration of proper hand 
support, workpiece support, and supply 
cord routing.

Fig. 5

Fig. 6

Fig. 7

Содержание 5008NB

















Отзывы: