9 ENGLISH
Lighting up the front lamp
CAUTION:
Do not look in the light or see the
source of light directly.
►
Fig.5:
1.
Lamp
To turn on the lamp, slightly pull the switch trigger, and
then release it. The lamp goes out approximately 10
seconds after releasing the switch trigger.
NOTICE:
When the tool is overheated, the lamp
flickers. Cool down the tool fully before operating
the tool again.
NOTE:
Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Overload warning lamp
►
Fig.6:
1.
Warning lamp
The warning lamp blinks when the tool is highly loaded.
If the load increases and the tool becomes overloaded,
the tool stops automatically and the warning lamp keeps
on lighting. In this case, release the switch trigger, and
remove the cause of overload, and then restart the tool.
NOTE:
When the warning lamp blinks, check the
following points:
•
The caulking material is clogged.
•
The speed adjusting dial is set to high speed.
•
The cutting area of the tip of the cartridge nozzle
or film type package is too small.
Drip preventive function
The motor keeps running for a short time even after the
trigger is released. It releases the pressure of the caulk-
ing material and prevents dripping.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing 300 ml size
holder
Installing or removing the holder
joint
Attach the holder joint and plate by securing the screws
firmly. To remove the holder joint, follow the installation
procedure in reverse.
►
Fig.7:
1.
Screw
2.
Plate
3.
Holder joint
Installing or removing the rod and
piston
1.
Insert the rod from the rear side of the tool with its
teeth facing down.
►
Fig.8:
1.
Short rod
2.
Attach piston A with the screw.
►
Fig.9:
1.
Screw
2.
Piston A
3.
Short rod
NOTICE:
Available type of caulking material
container for 300 ml size holder is cartridge only.
Be sure to attach piston A to the rod.
To remove the rod and piston, follow the installation
procedure in reverse.
Installing or removing the holder
CAUTION:
Secure the holder to the holder
joint firmly. Otherwise the holder may come off
during operation and may cause an injury.
To install the holder, turn it clockwise firmly until it stops
while holding the holder joint. To remove the holder,
follow the installation procedure in reverse.
►
Fig.10:
1.
Holder
Installing or removing 600 ml or 800
ml size holder
Installing or removing the holder joint
Attach the holder joint and plate by securing the screws
firmly. To remove the holder joint, follow the installation
procedure in reverse.
For 600 ml size holder
►
Fig.11:
1.
Screw
2.
Plate
3.
Holder joint
For 800 ml size holder
►
Fig.12:
1.
Screw
2.
Holder joint and plate
Selecting the type of piston
Select the proper type of piston according to the caulk-
ing material container by referring to the following table.
600 ml size
holder
800 ml size
holder
Cartridge
Piston A
Piston D
Film package
Piston B
Piston E *
Direct filling
Piston C
-
*. Optional accessary
Содержание 0088381850001
Страница 2: ...1 2 3 Fig 1 1 2 Fig 2 A B 1 2 Fig 3 1 Fig 4 1 Fig 5 1 Fig 6 1 2 3 Fig 7 1 Fig 8 2 ...
Страница 3: ...1 2 3 Fig 9 1 Fig 10 1 2 3 Fig 11 1 2 Fig 12 1 Fig 13 1 2 3 Fig 14 1 Fig 15 1 Fig 16 3 ...
Страница 4: ...1 Fig 17 1 Fig 18 Fig 19 1 2 Fig 20 1 Fig 21 1 2 Fig 22 Fig 23 1 4 2 3 Fig 24 4 ...
Страница 5: ...1 Fig 25 1 4 2 3 Fig 26 1 4 2 3 Fig 27 1 Fig 28 1 4 2 3 Fig 29 5 ...
