11 ENGLISH
Direct filling
NOTICE:
Make sure that 600 ml size holder
is attached to the holder joint and piston C is
attached to the rod. Do not use other type of
holder and piston for direct filling.
1.
Remove the holder cap, nozzle, and rubber ring
from the holder.
►
Fig.27:
1.
Holder cap
2.
Nozzle
3.
Rubber ring
4.
Holder
2.
Push the rod handle all the way until it stops.
3.
Insert the tip of the holder into the caulking mate-
rial, and then pull the rod handle slowly to fill the holder
with the caulking material.
►
Fig.28:
1.
Holder
4.
Attach the rubber ring, nozzle, and holder cap by
turning the holder cap firmly.
►
Fig.29:
1.
Holder cap
2.
Nozzle
3.
Rubber ring
4.
Holder
Caulking operation
Pull the trigger to feed the caulking material. Put one hand
under the holder to support the tool while operating it.
After the operation, wipe off the caulking material from the tool.
Be sure to remove the caulking material before it becomes solid.
NOTE:
At the beginning of operation, set the speed
adjusting dial to "1" and pull the switch trigger slowly to
check how much amount of caulking material is fed.
NOTE:
Depending on the type and conditions of
caulking material, it may not be fed at low speed. In
this case, set the speed adjusting dial higher.
NOTE:
If the caulking material is not fed, check the
following points:
•
The tip of cartridge nozzle is not cut adequately.
•
The caulking material is solid and clogged in the
nozzle.
•
The cartridge or package is damaged.
•
The caulking material is stiff. Warm the material
until it becomes soft.
•
The attached piston is not appropriate for the
type of caulking material.
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual.
The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
•
Piston A
•
Piston B
•
Piston C
•
Piston D
•
Piston E
•
300ml size holder set
•
600ml size holder set
•
800ml size holder set
•
Nozzle (for 600 ml size holder)
•
Nozzle (for 800 ml size holder)
•
Safety goggles
•
Makita genuine battery and charger
NOTE:
Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
Содержание 0088381850001
Страница 2: ...1 2 3 Fig 1 1 2 Fig 2 A B 1 2 Fig 3 1 Fig 4 1 Fig 5 1 Fig 6 1 2 3 Fig 7 1 Fig 8 2 ...
Страница 3: ...1 2 3 Fig 9 1 Fig 10 1 2 3 Fig 11 1 2 Fig 12 1 Fig 13 1 2 3 Fig 14 1 Fig 15 1 Fig 16 3 ...
Страница 4: ...1 Fig 17 1 Fig 18 Fig 19 1 2 Fig 20 1 Fig 21 1 2 Fig 22 Fig 23 1 4 2 3 Fig 24 4 ...
Страница 5: ...1 Fig 25 1 4 2 3 Fig 26 1 4 2 3 Fig 27 1 Fig 28 1 4 2 3 Fig 29 5 ...
