MAKINEX DPW-2500 Скачать руководство пользователя страница 37

Страница: 37 / 56

Page

TROUBLESHOOTING

TROUBLE SHOOTING GUIDE

PROBLEM

CAUSE

REMEDY

Pump does not reach the

specified pressures

Pump sucking air

Restore the tightness of the intake line

Intake flow rate insufficient

Increase the size of the intake pipelines
Remove and kinks from the pipes

Increase the filter capacity or clean the
filter cartridge
Increase the RPM to the rated speed

Worn intake and delivery valves

Replace the valves (1)

By-pass valve seat worn

Replace the valve

Worn gaskets

Replace the gaskets (1)

Unsuitable, worn nozzle

Replace nozzle

Faulty Gauge

Check and Replace

Irregular variations in

pressure

Worn intake and delivery valves

Replace the valves (1)

Valves blocked by dirt

Clean the valves (1)

Air being sucked into system

Restore the tightness of the intake
pipeline connections

Worn gaskets

Replace the gaskets (1)

Fluctuating pressure

Valves worn

Check and replace

Valves blocked

Check and replace

Pump sucking air

Check water supply and air ingress at
joints in suction line

Worn piston packing

Check and replace

Pressure drop

Nozzle worn

Replace Nozzle

Worn intake and delivery valves

Replace the valves (1)

Valves blocked by dirt

Clean the valves (1)

By-pass valve seat worn

Replace the valve

Worn gaskets

Replace the gaskets (1)

Pump noisy

Air being sucked into system

Restore the tightness of the intake
pipeline connections

intake and/or delivery valve
springs broken or collapsed

Replace the valves (1)

Valves blocked by dirt

Clean the valves (1)

Worn bearings

Replace the bearings (1)

Intake liquid temperature too high Reduce liquid temperature

Pump overheating

High pump operating pressure

Reduce the pressure to the rated values

Not enough water flowing
through

Check water inflow through pump

Pump left on idle for too long

DO NOT LEAVE PUMP ON IDLE FOR
>2min VOIDS WARRANTY

Содержание DPW-2500

























































Результаты поиска

Содержание DPW-2500

Отзывы:

Похожие инструкции для DPW-2500

Бренды по названию

Популярные бренды

MAKINEX DPW-2500, Руководство оператора

Результаты поиска

Содержание DPW-2500

Отзывы:

Похожие инструкции для DPW-2500

Бренды по названию

Популярные бренды