MAKINEX DPW-2500 Скачать руководство пользователя страница 8

Страница: 8 / 56

Page

WARNING

RISK OF FLUID INJECTION



The high pressure stream of water that this equipment

produces can cut through skin and its underlying tissues,

leading to serious injury and possible amputation. Spray

guns trap high pressure, even when engine is stopped and

water is disconnected, which can cause injury.



ALWAYS point spray gun in safe direction and squeeze trigger, to release high pressure,

every time you stop the engine.



NEVER aim spray gun at people, animal, or plants.



NEVER place hands in front of nozzle.



Make sure hose and fittings are tightened and in good condition. Never hold onto the hose or

fitting during operation.



DO NOT allow hose to contact muffler.



NEVER attach or remove wand or hose fittings while system is pressurised.



Use only hose and high pressure accessories rated for pressure higher than your pressure

washer’s psi.



To relieve system pressure, shut off engine, turn off water supply, and pull gun trigger until

water stops flowing.



DO NOT allow children to operate pressure washer.



NEVER direct the spray jet at any surface that may contain asbestos material.



DO NOT leave spray gun unattended while machine is running.



NEVER use a spray gun which does not have a trigger lock or trigger guard in place and in

working order.



ALWAYS be certain spray gun, nozzles and accessories are correctly attached.



ALWAYS wear personal protective clothing such as goggles, ear muffs, gloves, and closed

foot wear.

Содержание DPW-2500

























































Результаты поиска

Содержание DPW-2500

Отзывы:

Похожие инструкции для DPW-2500

Бренды по названию

Популярные бренды

MAKINEX DPW-2500, Руководство оператора

Результаты поиска

Содержание DPW-2500

Отзывы:

Похожие инструкции для DPW-2500

Бренды по названию

Популярные бренды