manualshive.com logo in svg

Majestic DBDV36IN, Руководство по установке, Страница: 54 / 73

Поделиться
Скачать
Majestic DBDV36IN Скачать руководство пользователя страница 54

54

Majestic  •  DBDV36IN, DBDV36IL, DBDV42IN, DBDV42IL Installation Manual  •  2397-980 Rev. B  •  5/16

11 

11 

Appliance Setup 

Figure 11.1  Fixed Glass Assembly

B. Remove the Shipping Materials/Inspect 

   

Grate 

Remove shipping materials from inside or underneath 

the 

fi

 rebox.  

•  The splatter guard is a piece of corrugated material 

used to protect the appliance during the installation 
process before 

fi

 nishing work on the whole hearth is 

complete. Splatter guards may be factory installed 
or accompany the decorative front of the appliance, 
depending on the 

fi

 replace model.  Splatter guards 

must be removed before appliance is 

fi

 red.

WARNING! Risk of Fire! 

Close the ball valve before in-

stalling the splatter guard to prevent accidental lighting. 
Remove the splatter guard before lighting the appliance.

•  Inspect the grate prior to installing the embers, logs 

and lava rock.  The grate tine on the right hand side 
should be parallel to the burner.  See Figure 11.2. If 
the grate is not parallel to the burner, contact your 
dealer.

A. Fixed Glass Assembly

WARNING! Risk of Asphyxiation! 

Handle 

fi

 xed  glass 

assembly with care. Inspect the gasket to ensure it is 
undamaged and inspect the glass for cracks, chips or 
scratches. 

• 

DO NOT

 

strike, slam or scratch glass.

• 

DO NOT

 

operate 

fi

 replace with glass removed, cracked, 

broken or scratched.

• 

Replace as a complete assembly.

Removing Fixed Glass Assembly

•  Pull the four glass assembly latches out of the groove 

on the glass frame. Remove glass assembly from the 
appliance.  See Figure 11.1.

Replacing Fixed Glass Assembly

•  Replace the glass assembly on the appliance. Pull out 

and latch the four glass assembly latches into the groove 
on the glass frame.

GLASS

ASSEMBLY

LATCHES

(BOTH BOTTOM 

AND TOP)

Figure 11.2  Grate Tine Parallel to Burner
                     (Appliance Shown with Optional Refractory Installed)

GRATE TINE PARALLEL WITH BURNER

GRATE TINE PARALLEL WITH BURNER

Содержание DBDV36IN










































































Отзывы:

Нет отзывов