Majestic 33BDVT Скачать руководство пользователя страница 24

33/36/39/43 BDVT 

-24- 

10002555/0

Vermont Castings, Majestic Products.

L

IGHTING

 

AND

 O

PERATING

 I

NSTRUCTIONS

For Fireplaces Equipped With SIT822 Gas Valve (EN or EP)

WARNING:  If you do not follow these instructions exactly, a re or explosion   

 

 

may result causing property damage, personal injury and loss of  life.

A.  This replace is equipped with an ignition device which 

automatically lights the pilot..  

DO NOT

 try to light the 

pilot by hand.

B. 

BEFORE OPERATING

, smell all around the appliance 

area for gas.  Be sure to smell next to the oor because 

some gas is heavier than the air and will settle on the 

oor.

 

What to do if you smell gas

 

•  Do not try to light any appliance.

 

•  Do not operate any electrical switch.

 

•  Do not use any phone in your building.

 

•  Immediately call your gas supplier from a  

 

neighbours phone.  Follow the gas suppliers  

 

instructions.

 

•  If you cannot contact your gas supplier call  

 

the Fire Department.

C.  Use only your hand to push in or turn the gas control 

knob.  Never use tools.  If the knob will not push in or 

turn by hand do not try to repair it, call a qualied service 

technician.  Force or attempting repair may result in a re 

or explosion.

D.  Do not use this appliance if any part has been under water.  

Immediately call a qualied service technician to inspect 

the appliance and to replace any part of the control system 

and any gas control which has been under water.

F

OR

 Y

OUR

 S

AFETY

 R

EAD

 T

HE

 F

OLLOWING

 W

ARNINGS

B

EFORE

 L

IGHTING

 T

HE

 A

PPLIANCE

L

IGHTING

 I

NSTRUCTIONS

1. 

STOP

!  Read the safety information above before con-

tinuing.

2.  Turn off all electrical power to the appliance.
3.  This appliance is equipped with an ignition device which 

automatically lights the pilot.  

DO NOT

 try to light the 

pilot by hand.

4.  Access the gas control by lowing the lower access door 

(louvre assembly).

5.  Turn the remote switch,if used, OFF.  Turn the wireless 

remote, if used, OFF.

6.  Wait ve (5) minutes to clear out any gas.  Then smell 

for gas, including near the oor.  If you smell gas STOP.  

Follow instructions B in the safety warnings above.  If you 

do not smell gas go onto the next step.

7.  Close the access door.
8.  Turn ON all electrical power to the appliance.
9.  Turn remote switch or wireless remote to ON
10.  If the appliance will not operate, follow the instructions 

TURNING OFF THE GAS TO THE APPLIANCE and 

call your service technician or gas supplier.

HI

LO

T

URNING

 O

FF

 T

HE

 G

AS

 T

O

 T

HE

 A

PPLIANCE

1.  Turn the remote switch to the OFF position.
2.  Turn OFF all electrical power to the replace if service 

is required.

3.  Open the lower access panel.
4.  Turn the shut-off valve on the exible gas line to the OFF 

position.

Gas Supply

Shut of valve

Flex Line

Valve in

the OFF position

Содержание 33BDVT



































Отзывы: