background image

18

83D0524

20/30/40ILDV Fireplace Insert

LOG PLAceMeNt

Before  you  begin

  -  This  unit  is  supplied  with  six  (6) 

ceramic fiber logs. Do not handle these logs with your bare 

hands. 

Always wear gloves to prevent skin irritation 

from ceramic fibers.

 After handling the logs, wash your 

hands gently with soap and water to remove any traces 

of fibers.

iNStALLiNG  LOGS  AND  ROcK  WOOL 

(eMBeR MAteRiAL) iN FiReBOx

1.  Break up rock wool (ember material) into dime-sized 

pieces. Place evenly as shown. Do not exceed 1" layer 

covering all round burner ports. 

Refer to Figures 16a 

and 16b.

2.  Do  not  cover  rectangular  slots  located  at  rear  of 

burner. 

LG536
ILDV
ember material
9/08

Ember Material

LG536

Figure 16b -

Place Ember Material

FP1968
ember material area
9/08

Ember Material Area

FP1968

Figure 16a -

Ember Material Area

Do not use the entire 

bag of rock wool to 

cover burner area.

W

ARN

iNG

the  positioning  of  the  logs  is  critical  to 

the safe and clean operation of this heater. 

Sooting and other problems may result if the 

logs are not properly and firmly positioned 

in the appliance. Never add additional logs 

or embellishments such as pine cones or 

vermiculite to the heater. Only use the logs 

supplied with the unit.
Failure to position the parts in accordance 

with diagrams below or to use only parts 

specifically approved for this heater may re-

sult in property damage or personal injury.

W

ARN

iNG

Содержание 20ILDVNV









































Отзывы: