Mahr Millimar C 1202 Скачать руководство пользователя страница 76

Страница: 76 / 88

Mahr GmbH • Millimar C1202

6.2

System 2

–

Press the ON/OFF key

Menu appears.

– Press

▼

and

to select

System 2

6.2.1 Updating module N 1700

The firmware file for the N 1700

module must first be copied to a

Micro SD card using a PC. The card

is then inserted into the C 1202.

–

Select the

Flash module

submenu

using the

▼

▲

key.

–

Select using

key or exit submenu

using the

key.

– Use

▼

▲

to select the firmware

file for the N 1700 module in use, or

exit the submenu using the

key.

Please check that the right firmware

file is saved on the Micro SD card.

If the wrong firmware is sent to

the N 1700 module, it will stop

working and will have to be sent to

Mahr Service.

–

Confirm selection by pressing key

Содержание Millimar C 1202

























































































Результаты поиска

Содержание Millimar C 1202

Отзывы:

Похожие инструкции для Millimar C 1202

Бренды по названию

Популярные бренды

Mahr Millimar C 1202, Руководство по эксплуатации

Результаты поиска

Содержание Millimar C 1202

Отзывы:

Похожие инструкции для Millimar C 1202

Бренды по названию

Популярные бренды