Mahr Millimar C 1202 Скачать руководство пользователя страница 30

Страница: 30 / 88

Mahr GmbH • Millimar C1202

–

Press the ON/OFF key

Menu appears.

–

Use the

key,

▼

or and

select the

Feature (M1 / M2 / M3)

you wish to configure.

–

Select the

Master

submenu using the

▼

▲

key.

–

Select using

key or exit submenu

using

key.

–

Use the

▼

key to select the digit and

the

▼

▲

keys to enter the relevant

value.

–

Use the

key to confirm the value or

to exit the submenu.

–

Use the key to switch to

measuring mode.

3.2.2.2 Two-point master measurement

In a two-point master measurement, two masters (gage blocks) of different sizes are

contacted in sequence and the actual values displayed are compared with the nominal

values indicated on the masters.

First, as for the one-point master measurement, the deviation from the nominal value is

calculated from the measurement on the first (smaller) gage block and then corrected.

The characteristic curve of the probe is thus shifted accordingly again in the display range

(in parallel) in the first step.

In a second step, a correction factor is calculated from the difference between the two

nominal values (max master - min master). This factor is used to change the pitch of the

characteristic curve of the probe in a linear fashion.

Содержание Millimar C 1202

























































































Результаты поиска

Содержание Millimar C 1202

Отзывы:

Похожие инструкции для Millimar C 1202

Бренды по названию

Популярные бренды

Mahr Millimar C 1202, Руководство по эксплуатации

Результаты поиска

Содержание Millimar C 1202

Отзывы:

Похожие инструкции для Millimar C 1202

Бренды по названию

Популярные бренды