background image

 

 

 

 

VL-VLP IM 13 JUNE 2017  

 

© 2017 Novatec, Inc. All Rights Reserved       

Page 22

 

 

 

 

 

 

 

Exclusions: 

 

Routine maintenance/replacement parts are excluded from the warranty. These include, but are not limited to: hoses, desiccant, filters, filter elements, wiper seals, gaskets, dew 
point sensors, infrared lamps, motors, internal solenoids, fuses and motor brushes. Use with abrasive materials will void the warranty of any standard product.  Wear resistant 
options may be available to extend usable service life with abrasive materials.

 

Novatec reserves the right to limit the warranty if the customer installs replacement parts that do 

not meet the specifications of the original parts supplied by Novatec. 

*Specific Exclusions: 

1. 

NovaDrier warranty is void if coalescing filters are not replaced on a 6-month or yearly basis (per instruction manual) and/or membrane has been 
exposed to ozone. 

2.     NovaVac Dryer -The ability of the canisters to hold vacuum will be compromised if the vacuum seal edge is damaged  
        from mishandling. We do not warranty canisters damaged from improper handling. We do, however, warranty the seals. 
3.     LOAD CELLS on our WSB’s are covered by Novatec standard warranty as long as they have not been damaged from  
 

improper handling. 

4.     Desiccant Wheel Warranty will be void if the wheel has been exposed to plasticizer, dust or other contaminants as a result 

of negligence on the part of the processor.  

This warranty shall not apply to equipment:  

1. 

Repaired or altered without written approval of NOVATEC unless such repair or alteration was, in our judgment, 
not responsible for the failure 

2. 

Which has been subject to misuse, negligence, accident or incorrect wiring by others 

3. 

Warranty is void if processing rates exceed manufacturer-recommended levels or if damage is caused by 

ineffective power isolation and/or power spikes/sags or incorrect installation. 

NOTE: All conditions and content of this warranty are subject to changes without notice. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание NOVATEC VL Series



























Отзывы: