Magnum Energy MagnaSine MS2012 Скачать руководство пользователя | Manualshive

Страница: 13 / 64

background image

Page 7

©

2009 Magnum Energy Inc

.

Installation

2.0 Installation

Info:

Installations should be performed by quali

fi

ed personnel, such as a licensed

or certi

fi

ed electrician. It is the installer’s responsibility to determine which safety

codes apply and to ensure that all applicable installation requirements are followed.

Applicable installation codes vary depending on the speci

fi

c location and application of

the installation.

CAUTION:

Review the “Important Product Safety Information” on page ii and the

“Important Battery Safety Instructions” on page iii before any installation.

CAUTION:

The inverter is heavy. Use proper lifting techniques during installation to

prevent personal injury.

The simpli

fi

ed system diagram shown in Figure 2-1 should be reviewed to assist you in planning

and designing your installation. This drawing is not intended to over-ride or restrict any national

or local electrical codes. This drawing should not be the determining factor as to whether the

installation is compliant, that is the responsibility of the electrician and the on-site inspector.

2.1 Pre-Installation

Before installing the inverter, read the entire installation section to determine how you are going

to install your MS inverter/charger. The more thorough you plan in the beginning, the better your

inverter needs will be met.

2.1.1

Unpacking and Inspection

Carefully remove the MS Series inverter/charger from its shipping container and inspect all contents.

Verify the following items are included:

The MS Inverter/Charger
Red and black DC terminal covers with Phillips screws
AC access cover with two Phillips screws
Two 5/16” Kep nuts (installed on the DC terminals).
Battery Temperature Sensor
Warning Label
MS Series Owner’s Manual

If items appear to be missing or damaged, contact your authorized Magnum Energy dealer or

Magnum Energy. If at all possible, keep your shipping box. It will help protect your inverter from

damage if it ever needs to be returned for service. Save your proof-of-purchase as a record of

your ownership; it will also be needed if the unit should require in-warranty service.
Record the unit’s model and serial number in the front of this manual in case you need to provide

this information in the future. It is much easier to record this information now, instead of trying

to gather it after the unit has been installed.

2.1.2

Required Tools and Materials

Hardware/Materials

Conduit, strain-reliefs and appropriate

fi

ttings

•

1/4” mounting bolts and lock washers

•

Electrical tape

•

Wire ties

•

Tools

Miscellaneous screwdrivers

•

Pliers

•

Wire strippers

•

Drill and drill bits

•

Pencil or Marker

•

Multimeter

•

Level

•

1/2” wrench

•

•
•
•
•
•
•
•

«
...
11
12
13
14
15
...
»

Содержание MagnaSine MS2012

































































Отзывы:

Нет отзывов

Похожие инструкции для MagnaSine MS2012

Бренд: La Marche Страницы: 18

Бренд: Eco Drive Страницы: 138

Бренд: B&B Electronics Страницы: 13

OmniConverter GPoE+/S

Бренд: OST Страницы: 10

Бренд: Lindy Страницы: 14

Бренд: York Страницы: 41

Бренд: Gesan Страницы: 80

Бренд: Kostal Страницы: 12

Бренд: TR-Electronic Страницы: 37

Бренд: Kohler Страницы: 88

Gold Link Dac III

Бренд: MSB Technology Страницы: 12

Бренд: Renishaw Страницы: 15

Бренд: tams elektronik Страницы: 48

SoundDock Series II

Бренд: Bose Страницы: 16

Бренд: Ryobi Страницы: 14

Profibus AMT58 13x12 PB Series

Бренд: Datalogic Страницы: 97

Бренд: Black Box Страницы: 2

Бренд: Toshiba Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды