Magnetrol Eclipse 706 Скачать руководство пользователя страница 25

Страница: 25 / 68

TOTAL_SP

: The set point for a batch totalization.

OUT

: The block output value and status.

OUT_RANGE

: The high and low scale values, engineering

units code, and number of digits to the right of the decimal
point associated with OUT.

GRAND_DENY

: Options for controlling access of host

computers and local control panels to operating, tuning,
and alarm parameters of the block (not used by the device).

STATUS_OPTS

: Allows you to select option for status

handling and processing. The supported status option for
the Integrator block is: “Uncertain if Manual mode.”

IN_1

: The block input value and status.

IN_2

: The block input value and status.

OUT_TRIP

: The first discrete output.

OUT_PTRIP

: The second discrete output.

TIME_UNIT1

: Converts the rate time, units in seconds.

TIME_UNIT2

: Converts the rate time, units in seconds.

UNIT_CONV

: Factor to convert the engineering units of

IN_2 into the engineering units of IN_1.

PULSE_VAL1

: Determines the mass, volume or energy per

pulse.

PULSE_VAL2

: Determines the mass, volume or energy per

pulse.

REV_FLOW1

: Indicates reverse flow when “true”; 0-

Forward, 1- Reverse

REV_FLOW2

: Indicates reverse flow when “true”; 0-

Forward, 1- Reverse

RESET_IN

: Resets the totalizers

STOTAL

: Indicates the snapshot of OUT just before a

reset.

RTOTAL

: Indicates the totalization of “bad” or “bad” and

“uncertain” inputs, according to INTEG_OPTIONS.

SRTOTAL

: The snapshot of RTOTAL just before a reset

SSP

: The snapshot of TOTAL_SP

INTEG_TYPE

: Defines the type of counting (up or

down) and the type of resetting (demand or periodic)

BE57-646 ECLIPSE Guided Wave Radar Transmitter - F

OUNDATION

fieldbus

™

Содержание Eclipse 706





































































Результаты поиска

Содержание Eclipse 706

Отзывы:

Похожие инструкции для Eclipse 706

Бренды по названию

Популярные бренды

Magnetrol Eclipse 706, Руководство по эксплуатации

Результаты поиска

Содержание Eclipse 706

Отзывы:

Похожие инструкции для Eclipse 706

Бренды по названию

Популярные бренды